Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wellborn Fence Installation: The Los Angeles Owner’s Guide
Wellborn fence installation in Los Angeles typically runs $4,130 to $10,620 installed, depending on fence run, material, and site conditions, and most residential jobs are completed in a single visit. We’re an independent installer, not affiliated with Wellborn, and we match your system to the correct components before anyone digs. Owners usually find out something failed the same way: a gate that sags and drags, a post that wobbles after a Santa Ana wind event, or panels that lean after the first heavy winter rain. One day it’s straight, the next it isn’t, and the fence tells you before you’re ready to hear it.
Which Wellborn Models This Applies To
Wellborn’s fence lines aren’t a single system. Their vinyl and composite runs use proprietary rail profiles and post caps, and the gate hardware kits are sized to specific post spacing. If you’re replacing a section, the model number is usually stamped on the inside face of a rail or on a post cap, and the fence run dimensions matter more than the label. Measure the post-to-post spacing and the rail height before you order anything.
The compatibility gotcha that catches most Los Angeles owners: Wellborn’s older vinyl profiles were made in nominal 6-foot and 8-foot sections, but the rail routing changed slightly on later runs. A replacement rail from a different production year won’t seat cleanly in the old post pockets without modification. This is the single most common mismatch we correct on Wellborn fences in Los Angeles.
On the OEM-versus-aftermarket question: for vinyl and composite, the aftermarket equivalents are good and often half the cost, but the post caps and gate hardware need to match Wellborn’s exact dimensions or the seal fails and water gets in. In Los Angeles, where UV exposure is relentless and marine air off the coast accelerates fading on anything west of the 405, a matched cap and hardware set matters more than the panel itself.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Wellborn Fence Installation Is Failing
- Posts that wobble at the base. The concrete footing has cracked or the soil has settled. Common in older Los Angeles lots where footings were poured shallow.
- Gates that drag or won’t latch. Hinge hardware has worn, or the post has shifted. Wellborn gate kits are heavy and the hinges take the load.
- Panels leaning after rain. Post rot or footing failure. Shows up fast in Los Angeles after the first real storm of the season.
- Rails pulling out of post pockets. The locking tabs or screws have backed out. On vinyl, this is usually a sign the original install didn’t account for thermal expansion.
- Fading, chalking, or cracking on the surface. UV breakdown. Inland Los Angeles neighborhoods like the Valley see this faster than coastal areas.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Wellborn fence installation in Los Angeles runs $4,130 to $10,620 installed for a typical residential run. The range depends on linear footage, whether you’re replacing a section or the whole fence, gate count, and whether the old concrete footings need to come out. Pulling old footings in hard Los Angeles clay adds labor. So does matching a discontinued Wellborn profile.
Our quotes are line-item: fence material, gate hardware, post footings, labor, and haul-away. Upfront pricing means the number you see is the number you pay. No change orders mid-job. The work is covered by our 730-Day Done Right Promise, which is one of the longest workmanship guarantees in residential construction.
DIY or Call Us?
You can safely check a few things yourself: whether posts are loose, whether gate hardware is worn, and whether rails are pulling out of their pockets. Photograph the model stamp on a rail or post cap before you call anyone.
Where DIY goes wrong: digging footings to the right depth, setting posts plumb in Los Angeles soil, and matching Wellborn’s gate hardware sizing. A post set two degrees off plumb will lean within a season. Gate kits installed without the right hinge spacing will bind, and you’ll replace the hardware twice. If you’re replacing a full run or a gate, that’s the point to call. Call (888) 427-1733 to schedule your free estimate.
FAQs
Most Wellborn vinyl and composite fences hold up 15 to 20 years in Los Angeles, with the inland Valley running shorter due to UV and heat cycling, and coastal neighborhoods running longer. Footings, not panels, are usually what fails first. Call (888) 427-1733 for an exact quote on your fence.
Yes, if the posts are sound and only a section, gate, or hardware has failed. A partial repair typically runs well under half a full replacement. If the footings are compromised, repair is a short-term fix. Call (888) 427-1733 for an exact quote.
A gate or single section can be done in one visit. A full fence run usually takes one to two days depending on footage and footing work. Most jobs are completed in a single visit.
We don’t keep Wellborn parts in stock and we don’t carry parts on trucks. We identify your profile from the model stamp and measurements, then source the matched part or approved equivalent before scheduling. This is why the first step is a photo and a measurement, not a promise.
We also work with KraftMaid, Cambria, and Silestone on adjacent projects when homeowners want a coordinated plan.
Ready to stop guessing? Call Groundwork Construction Co. of Los Angeles at (888) 427-1733 to schedule your free estimate. Calls are answered by a live person 24/7. You’ll get a line-item quote, background-checked uniformed technicians, and work backed in writing.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.