Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterBrick Paver Driveway in Los Angeles, CA
A brick paver driveway in Los Angeles typically runs $18 to $32 per square foot installed, and a standard two-car driveway of roughly 600 square feet usually lands between $11,000 and $19,000 depending on the paver type, base prep, and how much demolition the old surface requires. Brick pavers are the right call when you want real permanence: clay units that hold their color through decades of UV, individual pieces that can be lifted and reset instead of jackhammered out, and a surface that handles the shrink-swell clay soils common across the city far better than poured concrete. We install them with the base work most contractors skip, and every driveway we build is covered by our 730-Day Done Right Promise.
Groundwork Construction Co. of Los Angeles handles brick paver driveways as part of our Driveway & Pavers in Los Angeles service line, from tear-out and grading to the final polymeric sand and seal. Our technicians have up to 12 years of experience, they arrive in uniform and background-checked, and when you call (888) 427-1733 a live person picks up, day or night.
Why brick pavers hold up in Los Angeles specifically
This city sits on a patchwork of expansive clay soils and fills, and that matters for a driveway more than almost anything else. Clay swells when the winter rains soak in and shrinks through the long dry months, and a rigid slab fights that movement until it cracks. Individual pavers on a properly compacted aggregate base flex slightly and recover. That’s why a brick paver driveway in Los Angeles tends to outperform concrete over a 20-year horizon, even though the upfront number is higher. It’s also why base depth isn’t a place to cut corners here. We build to the soil we find, not to a single spec we use everywhere.
The other local reality is heat. Dark asphalt and bare concrete get hot enough to radiate through a late-afternoon valley summer. A light or mixed-tone brick paver surface stays noticeably cooler underfoot and holds its color rather than fading to chalky gray the way older concrete does.
Where these driveways make the most sense
Brick pavers earn their price on homes where curb appeal is part of the value story – a 1920s Spanish bungalow in Los Feliz, a Mid-Century post-and-beam in Sherman Oaks, a traditional two-story in Cheviot Hills. We match unit color, size, and laying pattern to the architecture so the driveway reads as part of the house, not a slab poured after the fact. We also work with modular and prefab home owners, and we coordinate our hardscape scheduling with partners like Cover and Dvele when a driveway is part of a larger site project, so the sequencing doesn’t stall your build.
When You Need Brick Paver Driveway
Most people call us for one of a handful of reasons. If any of these sound familiar, it’s worth a free estimate before the problem gets more expensive.
- Your concrete has cracked or heaved. We see this constantly in older San Fernando Valley neighborhoods where the clay moves seasonally. Once a slab has cracked and settled, patching is a band-aid. A paver driveway lets you rebuild the base right and gives you a surface that future movement won’t ruin.
- The driveway is puddling after rain. Poor original grading or a settled base leaves low spots that hold water and undermine whatever sits on top. We re-grade before a single paver goes down.
- You’re remodeling and the old surface drags down the whole look. A new kitchen and a tired, stained driveway under it can feel mismatched. Brick pavers tie the front of the house together without a full landscape redo.
- You’re adding a driveway or widening one. New construction, an ADU, or a second parking space means starting from bare ground – the ideal moment to specify brick pavers and get the base built right the first time.
- You want a surface you can repair piece by piece. If a utility line ever needs digging under the driveway, pavers lift and reset. A concrete slab gets cut and patched, and it never looks the same.
- You live on a slope and need a stable, non-slip surface. The hillside streets of Mount Washington and Silver Lake put real demands on a driveway. Textured pavers with a proper bedding layer grip better than a slick slab.
Our Brick Paver Driveway Process
Every job differs, but the sequence we follow on a Los Angeles brick paver driveway looks like this:
- On-site evaluation and free design consult. We look at the existing surface, drainage, soil, and how vehicles actually enter and exit. You get upfront pricing with no surprises – the number you see is the number you pay. We walk you through paver options, patterns, and how the driveway will meet the street and any adjoining walks.
- Permits and utility checks. Driveways in Los Angeles interact with the public right-of-way, and any change to a driveway apron or curb cut involves the city. We identify what’s needed for your specific property and check for buried utilities before anyone starts digging, so nothing gets hit and no inspection stalls the job.
- Tear-out and base prep. We remove the old surface and excavate to depth, then build a compacted aggregate base in lifts. This is the step that decides whether the driveway lasts. We grade for drainage first so water runs off and away rather than sitting against your foundation or pooling at the garage door.
- Bedding layer and paver installation. A leveled sand or fine-aggregate bedding layer goes down, then the pavers are set in the pattern you chose, cut clean at edges, and checked for consistent slope and finish as we go.
- Edge restraint and joint sand. Restraints lock the field in place so the pavers don’t creep, then joints get filled with polymeric sand that hardens and resists washout – a real upgrade in a region that gets both dry spells and concentrated winter storms.
- Final walkthrough and seal. We do a full walkthrough with you, confirm drainage and finish, and apply sealer if you’ve chosen it. Then the 730-Day Done Right Promise backs the workmanship – if something isn’t right, we make it right.
Brick Paver Driveway Pricing in Los Angeles
Brick paver driveway cost in Los Angeles depends on square footage, paver type, base conditions, and how much prep your site needs. Here’s an honest breakdown of what to expect:
| Line item | Typical range |
|---|---|
| Clay brick pavers, installed | $18 – $32 per sq ft |
| Concrete pavers (brick-look), installed | $12 – $22 per sq ft |
| Tear-out of old concrete or asphalt | $2 – $5 per sq ft |
| Extra base excavation and grading | $4 – $9 per sq ft |
| Sealing | $1.50 – $3 per sq ft |
| Driveway apron / curb-cut work | quoted per site |
What pushes a quote toward the top of the range? Heavy demolition, poor or unstable soil that needs deeper base work, complex patterns like herringbone with multiple colors, tight access where a machine can’t reach, and significant regrading or drainage correction. What keeps it down? A sound existing base, a straightforward rectangular layout, and a single-tone running bond pattern.
A typical 600 square-foot two-car driveway lands around $11,000 to $19,000 installed for genuine clay brick pavers, all-in. Wider driveways, RV pads, and long hillside runs scale up from there. We put the full number in writing upfront, and you can pair it with 0% financing for 18 months plus $1,000 off projects over $10,000. Estimates and design consults are free – call (888) 427-1733 and we’ll get you a real number.
FAQs – Brick Paver Driveway
How much does a brick paver driveway cost in Los Angeles?
A brick paver driveway in Los Angeles typically costs $18 to $32 per square foot installed, so a standard 600-square-foot two-car driveway usually runs $11,000 to $19,000. Tear-out, extra base work, and sealing can add to that, while a simpler pattern and sound existing base keep it lower. Call (888) 427-1733 for an exact quote – estimates are free and the price we give is the price you pay.
Are brick pavers better than concrete for a Los Angeles driveway?
Yes, in most Los Angeles conditions brick pavers outperform concrete over time because they flex with the city’s expansive clay soils instead of cracking, and individual units can be lifted and reset rather than replaced wholesale. The upfront cost is higher, but the lifespan and repairability usually win out. We’ll tell you honestly which makes more sense for your specific property.
How long does a brick paver driveway take to install?
Most residential brick paver driveways take roughly three to seven days from tear-out to final sand, depending on size, demolition, and base conditions. A small, straightforward driveway can finish in a few days, while a large or heavily regraded job runs longer. We confirm a realistic timeline before we start so you can plan around the disruption.
Do I need a permit for a brick paver driveway in Los Angeles?
A permit is often required when the work touches the public right-of-way, such as a new or altered driveway apron or curb cut, and requirements vary by property and street. We check what applies to your address and handle the process as part of the job. Call (888) 427-1733 and we’ll walk you through it – estimates are free.
Can you redo just part of an existing paver driveway?
Often, yes. Because pavers are individual units, we can lift and reset a damaged section, correct a low spot, or replace broken pieces without tearing out the whole driveway, provided the surrounding base is still sound. We assess that on site and tell you whether a targeted repair or a full rebuild makes more sense.
How do I maintain a brick paver driveway in Los Angeles?
A brick paver driveway stays low-maintenance here: sweep or rinse off debris, top up joint sand occasionally, and reseal every few years to keep color and help resist staining. That’s it. The surface won’t need patching or crack repair, and it handles both the dry season and winter rain without the upkeep a slab demands.
If you’re ready to replace a cracked, dated, or puddling driveway with a surface built to last and backed in writing, call Groundwork Construction Co. of Los Angeles at (888) 427-1733. A live person answers around the clock, the estimate and design consult are free, and every brick paver driveway we install carries the 730-Day Done Right Promise – if it’s not done right, we make it right. Start with our home page to see the full range of what we build, then let’s get your driveway on the schedule.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles.