Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
American Standard Kitchen Remodeling: The Los Angeles Owner’s Guide
We install American Standard-compatible kitchen fixtures and finish components, and a full kitchen remodel in Los Angeles runs $16,520 – $53,100 installed, with smaller scope projects landing between $10,620 and $23,600. If you’re replacing a single failed American Standard fixture or fitting rather than the whole room, most jobs are completed in a single visit once the correct part is matched to your model. Owners usually find out something’s wrong the hard way: a faucet that drips overnight, a sprayer that won’t seat, a drain assembly that backs up, or a supply line that weeps onto the cabinet floor in a Pasadena bungalow or a 1920s Tudor in Hancock Park. We’re an independent service provider and not affiliated with American Standard, so when we quote a replacement we tell you plainly whether an OEM part or a quality equivalent is the right call.
- The short version: Most American Standard kitchen failures are wear parts (cartridges, seats, sprayer heads, supply lines, drain assemblies), not the fixture body itself.
- Installed remodel range: $16,520 – $53,100 for full scope; $10,620 – $23,600 for small kitchens.
- Timing: Single-part swaps are typically one visit; multi-fixture or layout work gets scheduled on a written plan.
- Backed by: The 730-Day Done Right Promise and upfront pricing with no change-order surprises.
Which American Standard Models This Applies To
American Standard’s kitchen side covers a wide spread: single-handle pull-down and pull-out faucets (the Fairbury, Beale, and Portsmouth lines among them), two-handle traditional decks, bar and prep sinks, and the under-sink drain and supply components that go with them. The compatibility gotcha most owners miss is that American Standard cartridge and seat assemblies are series-specific, not universal. A cartridge that fits a Fairbury pull-down will not seat correctly in a Portsmouth two-handle body, and the thread pitch and O-ring stack differ between them. Before you buy anything, pull the faucet’s model number off the tag under the deck plate or inside the cabinet door, and photograph the cartridge you remove next to a ruler. If the tag is gone, we identify the assembly by measuring the stem length and cartridge diameter against the American Standard spec sheet for that series.
On the OEM-vs-aftermarket question, our honest take: for cartridges and seats, American Standard OEM parts are worth the modest premium because the tolerances matter and aftermarket brass runs soft. For supply lines, sprayer heads, and drain gaskets, a quality equivalent performs every bit as well. We source through plumbing supply houses, and if a part has to be ordered we tell you the lead time upfront instead of guessing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your American Standard Kitchen Remodeling Is Failing
- A steady drip from the spout with the handle off. This is almost always a worn cartridge seat or a scored ceramic disc. In our experience the drip starts small and worsens over weeks as mineral scale from Southern California’s hard water builds on the seat.
- The handle feels stiff or grinds when you turn it. Grit and scale have worked into the cartridge stem. Left alone, the stem eventually seizes and you’re turning a handle that no longer moves the valve.
- The sprayer head won’t return or dribbles. A stretched or clogged sprayer hose and a mineral-blocked head are the usual culprits, common in kitchens that see heavy daily use.
- Water pooling inside the cabinet under the sink. Supply line fittings and the drain basket are the first to go. On older American Standard drain assemblies the rubber gasket under the sink flange hardens and cracks, and that leak can quietly rot a cabinet floor.
- Low or uneven flow from the aerator. Sediment and scale in the aerator screen, made worse by the mineral content of Los Angeles tap water. A quick soak often restores flow, but persistent low pressure points to the cartridge or supply line.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what projects cost in Los Angeles, parts and labor included, quoted line by line so you see exactly where the money goes:
| Project | Installed Range (Los Angeles) |
|---|---|
| Full kitchen remodel | $16,520 – $53,100 |
| Small kitchen remodel | $10,620 – $23,600 |
| Cabinet installation | $4,720 – $15,340 |
| Countertop installation | $2,360 – $7,670 |
| Backsplash installation | $945 – $2,950 |
| Kitchen island installation | $3,540 – $11,800 |
What drives the range: layout changes, cabinet and counter material selection (we work with Cambria, Silestone, and KraftMaid alongside American Standard fixtures), and whether plumbing and electrical need to move. Every estimate is itemized, and the number you see is the number you pay. All workmanship is covered by the 730-Day Done Right Promise, and we offer 0% financing for 18 months plus $1,000 off projects over $10,000.
DIY or Call Us?
You can safely check a few things yourself. Look under the sink for moisture, wipe the aerator clean, confirm the model tag, and note whether the drip happens at the spout or the handle. Those are diagnostic, not repair. Where DIY goes wrong on American Standard kitchen plumbing is the valve work: pulling a cartridge out of a corroded body can shear the stem inside the faucet, and a cross-threaded supply fitting under pressure will flood the cabinet. We also see owners replace the faucet when the real problem is a $6 gasket, or vice versa. Most single-part swaps are completed in a single visit by a background-checked, uniformed technician, and our calls are answered by a live person 24/7. Call us at (888) 427-1733 for a free estimate and an honest read on what’s actually failing.
FAQs
A quality American Standard cartridge typically lasts 8 – 12 years, but Los Angeles’s hard water shortens that. Scale buildup is the main reason we see cartridges fail closer to the 6 – 8 year mark in high-mineral neighborhoods. If yours is dripping, call (888) 427-1733 for a free estimate.
Often, yes. Worn cartridges, seats, aerators, sprayer heads, and supply lines can usually be replaced without swapping the faucet body, which saves real money. We assess on arrival and only recommend a full replacement when the body itself is cracked or the valve seat is beyond resurfacing. Call (888) 427-1733 and we’ll tell you straight.
A cartridge, sprayer, or supply line replacement is typically completed in a single visit, usually under two hours. A full faucet or multi-fixture job is scheduled on a written plan so you know what to expect. Call (888) 427-1733 to book your free estimate.
We source through plumbing supply houses and order the OEM assembly matched to your model series, and if it isn’t in local stock we give you the real lead time before work starts. For common wear parts we often have a quality equivalent on hand same day. Call (888) 427-1733 for pricing on your specific model.
Ready to stop the drip and get your kitchen working again? Call Groundwork Construction Co. of Los Angeles at (888) 427-1733 for a free estimate – live person, 24/7, upfront pricing, and the 730-Day Done Right Promise behind every job. We also service KraftMaid, Cambria, and Silestone, so whether you’re chasing one American Standard part or planning a full Los Angeles kitchen remodel, one call covers it from foundation to finish line.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.