Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
American Standard Driveway & Pavers: The Los Angeles Owner’s Guide
We install American Standard driveway and paver systems across Los Angeles, and a full paver driveway typically runs $8,260 to $21,240 installed. Concrete runs $5,310 to $14,160, and asphalt paving $4,130 to $10,620. Replacement sits at $5,900 to $16,520, and resealing a paver or concrete surface is $295 to $825. We’re an independent contractor, not affiliated with American Standard, and every project is backed by our 730-Day Done Right Promise.
Most owners don’t notice a failing driveway until it’s obvious: water pooling against the garage threshold after a rain, a paver lifting in the afternoon heat, or a hairline crack that widened over one summer. Los Angeles driveways take a specific beating – intense UV, long dry stretches, then concentrated winter rain on clay-heavy soil – and that cycle is usually what starts the failure.
Key Takeaways
- Paver driveway install: $8,260-$21,240. Concrete: $5,310-$14,160. Asphalt: $4,130-$10,620.
- Resealing extends life for $295-$825 – the cheapest fix on this list.
- Most damage in Los Angeles traces to drainage and base prep, not the surface material.
- Upfront pricing, no surprises – the number you see is the number you pay.
Which American Standard Models This Applies To
American Standard paver systems show up across a range of residential profiles, and matching your product correctly depends on the spec sheet, not the look of the surface. American Standard publishes product data by collection and profile, and the label or spec tag – usually on the original project documentation or stamped on the underside of a loose unit – tells you the exact series, dimensions, and finish. Measure a single unit’s length, width, and thickness with a tape; a tolerance of even 1/8 inch matters when you’re patching into an existing field.
The compatibility gotcha here: American Standard’s paver profiles have shifted thickness standards across production runs, and a nominal 60mm paver from one production batch won’t always sit flush with a current one. If you’re matching into existing work, we compare the actual measured thickness and the joint spacing on your driveway before ordering a single unit.
OEM versus aftermarket is a real decision. OEM keeps the color lot and texture consistent with what’s already down. Quality aftermarket equivalents can cost less and match dimensionally, but color variation across a large field is far more visible in Los Angeles sunlight than most people expect. We walk you through both. We also service KraftMaid, Cambria, and Silestone for homeowners doing concurrent interior work.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your American Standard Driveway & Pavers Is Failing
- Pavers rocking or lifting at the edges. The bedding layer has lost fines or the base wasn’t compacted to depth. Once a paver moves, water gets underneath and the movement spreads edge to edge across the field.
- Standing water after rain. This is a grading and slope problem, not a paver problem. It often shows up where the driveway meets the apron or a garage threshold, and it erodes base material every cycle.
- Hairline cracks or joint sand washing out. Polymeric joint sand failing is a symptom of movement underneath. Missing joint sand means water is entering the base and the erosion has usually already started.
- Sun-faded or chalking surface. Los Angeles UV is unforgiving; some finishes chalk and fade faster than the pavers themselves degrade. Sealing on schedule prevents it.
- Efflorescence (white powdery haze). Mineral salts pushed to the surface by moisture moving through the slab or pavers. Persistent efflorescence usually means water is trapped in the base, not just on top.
Replacement Cost & What’s Included
In Los Angeles, a full American Standard paver driveway install runs $8,260 to $21,240, and driveway replacement is $5,900 to $16,520. The range is driven by square footage, removal and disposal of the old surface, base depth and compacting, paver selection, edging, and drainage correction – the last item is the one most bids leave out.
| Work | Los Angeles Range |
|---|---|
| Paver driveway installation | $8,260-$21,240 |
| Concrete driveway installation | $5,310-$14,160 |
| Asphalt driveway paving | $4,130-$10,620 |
| Driveway replacement | $5,900-$16,520 |
| Driveway sealing | $295-$825 |
| Paver patio installation (adjacent) | $4,130-$12,980 |
Every estimate is line-itemed – removal, base, material, labor, cleanup – so you see exactly where the money goes. Workmanship is covered in writing under the 730-Day Done Right Promise. If it’s not done right, we make it right.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely do a few things yourself: measure the failing area, photograph the water pooling, pull a loose paver to check the bedding sand, and read your spec tag to identify the exact American Standard product. That’s information, not installation.
Where DIY goes wrong: driveway installation is a base and compaction job before it’s a surface job. A paver field laid by hand without a properly compacted, sloped base will look right for one season and start moving in the next rain cycle. Correcting base depth and grading under a Los Angeles driveway is real excavation work – not a weekend bucket-and-trowel job. And if a paver or slab lifts near the garage or a step, don’t leave it open to water. Call us at (888) 427-1733 and we’ll give you a straight read on what’s failing and what it actually costs to fix.
Calls are answered by a live person, 24/7. No voicemail, no delays.
FAQs
A properly installed paver driveway typically lasts 25 to 50 years, and resealing every 3 to 5 years in Los Angeles UV extends that. In our dry summers and concentrated winter rains, sealing timing matters more than most of California; skip it and surface fading and joint sand loss arrive early. Most failures we see trace back to base preparation, not the material itself. Call (888) 427-1733 for a free evaluation.
Yes – if the failure is localized, we can lift, re-set, and re-sand a section without a full replacement. Whole-driveway replacement only makes sense when base failure or drainage is widespread; a single rocking section near the edges is usually a repair. The honest answer depends on how far the water issue goes. Call for an exact quote – estimates are free.
A typical residential American Standard driveway install takes 2 to 4 days depending on square footage, base correction, and drainage work. Small repairs are often done in a single visit. We’d rather give you a real timeline upfront than a fast promise we can’t keep, and we’ll tell you exactly what to expect in the written estimate. Call (888) 427-1733 to schedule.
We source to the exact spec tag on your existing product, confirming series, dimensions, thickness, and color lot before ordering – we don’t stock parts and we don’t guess on a match. Any part that can’t be matched exactly, we tell you before work starts. Call us for a free estimate – we’ll identify your product and quote it line by line.
Get It Done Right
Groundwork Construction Co. installs American Standard driveway and paver systems across Los Angeles with upfront pricing and the 730-Day Done Right Promise behind every job. From foundation to finish line, one contractor handles it, and our technicians have up to 12 years of experience. Financing is available at 0% for 18 months, and projects over $10,000 get $1,000 off. Call (888) 427-1733 for your free estimate and design consult – a live person answers, day or night.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.