Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CertainTeed Bathroom Remodeling: The Los Angeles Owner’s Guide
We install bathroom remodeling systems built around CertainTeed tile backer board and moisture-resistant gypsum assemblies in Los Angeles, and a full bathroom remodel here typically runs $10,620 – $33,040 depending on square footage, tile selection, and how far the scope reaches. Most Los Angeles owners don’t go looking for a CertainTeed backer board failure until something visible forces them to: a soft spot under a toe kick, a tile that shifts when you step on it, or grout that keeps cracking along the same shower wall no matter how many times it’s patched. Those are the three calls we get most, and all three trace back to the substrate underneath the tile, not the tile itself.
Which CertainTeed Models and Products This Applies To
CertainTeed’s bathroom-relevant line centers on backer board and moisture-resistant drywall products rather than finished fixtures, so “matching a part” here means matching a substrate panel to the condition underneath it. The backer board family runs in standard thicknesses (commonly 1/4-inch and 1/2-inch panels, with the thicker panel used on floors and walls where deflection matters), and the moisture-resistant gypsum panels are marked for interior wet-area use only, not for shower pans or direct water contact. The identification step is the one owners skip: pull the manufacturer stamp off the exposed edge or the back of a cut panel before anything new gets ordered, because panel thickness and the rating printed on that stamp determine what can legally replace it in a wet zone.
The OEM-versus-aftermarket decision matters more here than on a fixture. A genuine CertainTeed panel matched to the existing assembly keeps the system behaving as designed. A cheaper cement board of the same nominal thickness often has a different screw pattern requirement and a different vapor profile, and in Los Angeles bathrooms that mix marine-layer humidity with dry Santa Ana weeks, a mismatched panel is where delamination starts. We’re an independent service provider and not affiliated with CertainTeed, so we match the part honestly rather than steering you to whatever a supplier happens to push that week. If you also need cabinetry or countertop work in the same bathroom, we handle KraftMaid, Cambria, and Silestone alongside it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CertainTeed Bathroom Remodeling Is Failing
The symptoms below are what actually prompt the call. Each one points to a cause, and the cause determines the repair.
- Grout cracking in the same line repeatedly. The substrate is flexing under the tile, usually from a panel that was screwed to code spacing on the edges but skipped in the field. Patching grout hides it for a season at most.
- A soft or spongy spot at the shower curb or floor edge. Water has reached the panel edge or the framing behind it, and the board has begun to break down. This is the point where the cost of waiting climbs fast.
- Tile popping loose with a hollow sound when tapped. Thin-set lost its bond to the panel, often from a dusty surface or the wrong mortar for the board type. A hollow tap over a 2-foot area means the panel is suspect too.
- Musty smell that returns after every cleaning. Moisture is trapped behind the tile assembly, and the symptom will keep coming back until the panel and any wet framing are exposed and dried.
- Visible swelling or crumbling at a cut edge. Moisture-resistant gypsum was used too close to direct water, or the cut edge was never sealed. Panels stamped for wet-area use only don’t belong in a shower pan.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full bathroom remodel in Los Angeles runs $10,620 – $33,040, and a smaller bathroom scope lands at $5,900 – $14,160. If the failure is localized, targeted repairs price lower: a shower replacement runs $3,540 – $10,030, a walk-in shower installation $5,310 – $14,160, and a tub-to-shower conversion $4,130 – $11,800. A vanity installation, if the tear-out reaches that far, is $945 – $3,540.
What drives the range is square footage of tile, whether framing behind the panel is wet and needs replacement, and how much of the room gets opened up while the wall is already exposed. Our quotes are line-item and written, so you see panel material, thin-set, waterproofing, and labor as separate numbers rather than one lump. The number you see is the number you pay. Every project carries our 730-Day Done Right Promise, so if the workmanship fails inside that window, we make it right.
DIY or Call Us?
An owner can safely do the detective work: tap the tile with a screwdriver handle and listen for hollow spots, press the floor near the curb and shower edges for give, and photograph the manufacturer stamp on any exposed panel edge. What we’d steer you away from is pulling tile and replacing backer board yourself. Behind that tile sits framing that may be wet, a waterproofing layer that has to tie into the pan correctly, and a screw pattern that has to land on studs at the right spacing or the new panel flexes exactly like the old one. A bathroom that leaks again in eight months costs more than doing it once. If anything you’ve found points to a soft spot or a returning smell, call (888) 427-1733 and we’ll schedule a free estimate.
FAQs
Properly installed and waterproofed, the substrate should outlast the tile on top of it, easily 20 years or more. What shortens that in Los Angeles is the swing between coastal humidity and dry inland heat, plus a shower that never gets a chance to dry out between uses. Call (888) 427-1733 for an exact quote on your bathroom; estimates are free.
Sometimes a single compromised section can be cut out and patched if the failure is isolated and the surrounding panel tests sound. If the soft spot spreads past a couple of square feet, or the framing behind it is wet, replacement of the affected wall or floor assembly is the honest answer. We’ll tell you which one you’re looking at after we open it up.
A localized panel and tile repair is usually a few days once materials are on site. A full bathroom remodel in Los Angeles typically runs several weeks, and we give you the schedule in writing before work starts. Call (888) 427-1733 to get a free estimate and a realistic timeline for your bathroom.
We read the stamp on the existing panel, confirm thickness and rating, and order the matching board through verified suppliers rather than substituting a same-size product that behaves differently. That’s how the repair holds. We’re not affiliated with CertainTeed; we simply match what’s already in your wall.
Whether you’re pricing a full bathroom remodel or a targeted repair, our team answers the phone live, 24 hours a day, and every technician who shows up is background-checked and arrives in uniform. Projects over $10,000 get $1,000 off, and 0% financing for 18 months is available if spreading the cost helps. Call Groundwork Construction Co. of Los Angeles at (888) 427-1733 for a free project estimate and design consult, and we’ll walk your Los Angeles bathroom with you before a single panel comes down.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.