Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Home Additions & ADU: The Los Angeles Owner’s Guide
We build and finish home additions and ADUs using Boral exterior trim, siding and cladding systems, and a typical Los Angeles addition runs $53,100 to $153,400 installed (a full ADU runs $106,200 to $259,600). If the Boral component on your existing structure has failed, we can match and replace it. Most owners figure out something’s wrong when a joint on the Boral trim opens up after a hot week, or when they spot bubbling paint on the shadow line above the patio slab. Groundwork Construction Co. of Los Angeles is an independent construction company. We are not affiliated with Boral.
What follows covers how Boral trim and cladding behave on Los Angeles structures, what fails first, what a replacement costs here, and where DIY goes wrong.
Which Boral Models This Applies To
Boral’s residential exterior products fall into a few families, and knowing which one you have changes what part you’re ordering. Boral TruExterior trim comes in several profiles (flat boards, shiplap, beadboard, and a range of fascia and frieze styles), with nominal dimensions that match dimensional lumber but different actual thicknesses. Boral Versetta Stone panels are a separate system with their own corner pieces and ledgers. If you’re working with an older install, some Boral profiles have been discontinued or renamed, and the fastest way to identify your part is the back of a removed piece or a stamped stamp on the panel edge – not the paint color.
Measure actual thickness with a caliper, not a tape. Boral TruExterior flat trim typically runs slightly thinner than a nominal 1x, and a mismatched board will show a lip at the joint that no amount of caulk hides. Snap the profile and carry it to the supplier. Bring the fastening spec too: the screw pattern on your existing install tells you what the original used.
On the OEM-versus-aftermarket question, Boral is one of the few categories where the original manufacturer part is usually worth it. Matching profiles and paint-receptive surfaces are the whole point. A quality aftermarket PVC or composite equivalent can work in specific spots, but we recommend it only for concealed areas.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Home Additions & ADU Is Failing
- Paint bubbling or flaking on the shadow line. Moisture is getting behind the board or the end grain wasn’t sealed. In Los Angeles this shows up most on south- and west-facing walls after a wet winter.
- Open joints or gaps at miters and butt splices. Thermal cycling pulls the joint apart when fasteners aren’t set with the right gap. If the gap is wider than a credit card, the joint has moved.
- Soft spots or swelling at the base of a panel. The bottom course is wicking water off the slab or deck. Once a Boral panel takes on water it doesn’t bounce back the way real wood sometimes does.
- Visible fasteners popping through the face. Screws that walked out or were overdriven are a sign the substrate moved under the board, usually because the framing or sheathing wasn’t flat.
- Chalking or color shift on a Boral cladding panel. UV exposure in Los Angeles is hard on any painted surface, but uneven color tells you one panel lot differs from the rest.
Replacement Cost & What’s Included
| Scope | Los Angeles Range |
|---|---|
| Home addition (full build) | $53,100 – $153,400 |
| ADU construction | $106,200 – $259,600 |
| Garage conversion | $35,400 – $94,400 |
Part replacement on an existing Boral install runs far less than a full addition. What drives the number: linear footage of trim or panel, whether the substrate has to be repaired behind the board, how high the work sits (a second story adds labor and scaffold), and whether the profile is current stock or a discontinued line. Our quotes are line-itemed: material cost, labor, and what we’re removing shown separately, and the number you see is the number you pay. The work carries our 730-Day Done Right Promise. We give you a written scope before any board comes off.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely check for failed caulk, tap on a panel to listen for hollow spots, and photograph the back of a removed piece for identification. What goes wrong for owners is the fastening and flashing sequence. Boral trim expands and contracts, and the wrong gap or the wrong fastener length shows up in a failed joint within a season. Where a panel meets a roof or a window head, the flashing layering has to be in the right order or water tracks behind the board.
If your structure is more than a few feet off the ground, we don’t recommend ladder work on a trim tear-out. Call us and we’ll do the inspection. We answer the phone with a live person 24/7. Call (888) 427-1733 for a free estimate.
FAQs
Boral TruExterior trim is engineered to hold up well past 20 years in a dry-to-wet climate like Los Angeles, but the paint film and the joint seals are what determine whether you see that. Plan on recoating every 7 to 10 years given our UV load, and check joints annually after the rainy season.
Sometimes. A single cracked or water-damaged panel can often be swapped without touching the rest of the field if the profile is still in production. If the substrate behind it has rotted, the repair becomes a rebuild of that section. We’ll tell you which one you’re looking at before any work starts.
A single-panel replacement on an accessible wall is typically a same-day job. A multi-wall section or a second-story run is usually several days, mostly because of staging and paint cure time. We schedule and price the scope, then hold to it.
We work through established Boral distributors and verify the profile against your removed part or the manufacturer’s current spec sheet before ordering. If the exact profile is discontinued, we’ll show you the closest current match and where the difference will show. Call (888) 427-1733 to get your part identified and priced.
Ready to Get It Priced?
Groundwork Construction Co. of Los Angeles handles the full scope, from matching the Boral profile to finishing and paint, and our technicians have up to 12 years of experience on exterior systems. We also service KraftMaid, Cambria and Silestone on the interior side if your addition involves a kitchen or bath. Projects over $10,000 get $1,000 off, we offer 0% financing for 18 months, and every estimate is free. Call (888) 427-1733 to get your Los Angeles project moving.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.