Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Fence Installation: The Los Angeles Owner’s Guide
PGT fence installation in Los Angeles typically runs $4,130 to $10,620 installed, and the exact number depends on footage, material, terrain and gate count. Most residential runs are completed in a single visit once the layout and permits are settled. We’re Groundwork Construction Co. of Los Angeles, an independent contractor, and we install fence systems built around PGT-spec hardware and components.
Owners usually find the problem the same way: a gate that drags on the driveway, a post that’s leaning after a Santa Ana wind event, or pickets pulling loose along a run that looked fine two seasons ago. By the time you’re reading this page, the failure is already visible. The good news is that fence failures are almost always diagnosable in a single walk of the property. We’ll tell you exactly what failed, what it’ll cost to fix or replace it, and whether the fix is a repair or a full run rebuild.
Which PGT Models This Applies To
PGT is best known for its impact-rated windows and doors, and many Los Angeles properties built or renovated in the last two decades carry PGT products – particularly PGT WinGuard and PGT Aluminum series that meet Florida-style and coastal impact standards. PGT doesn’t manufacture fence components as a standalone line. What “PGT fence installation” means in practice is fence systems built to the same material and hardware standards as PGT-rated exterior products: impact-rated aluminum, powder-coated steel, and hardware rated for the same wind-load and salt-air conditions PGT’s window lines are engineered for. That distinction matters because a Los Angeles fence on a canyon parcel or a coastal-facing lot is exposed to the same weather that drove the PGT spec on the house in the first place.
If you’re not sure what your fence currently uses, here’s how to identify it before you buy anything:
- Measure the post spacing. Standard runs in Los Angeles sit at 6 ft or 8 ft on center. PGT-spec aluminum runs often use a tighter 6 ft on-center spacing to meet wind-load ratings on exposed sites.
- Check the hardware stamps. Post brackets and gate hinges carry manufacturer marks. A non-PGT gate hinge on a PGT-rated panel is the most common failure point we find.
- Look at the post base. Powder-coated steel posts set in concrete with a cast base plate will outlast a galvanized post in coastal Los Angeles every time.
OEM vs. aftermarket: for fence hardware, an aftermarket post bracket or hinge from a known builder is fine if it’s rated for the same wind load. For the structural panel itself – particularly impact-rated aluminum – we source from suppliers who match the original spec, not from whichever yard has stock that week. There’s no reason to downgrade a rated assembly to whatever’s cheap.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your PGT Fence Installation Is Failing
Fence failures in Los Angeles look different from other parts of the country because of the seasonal pattern here: dry summers, then a rainy stretch, then Santa Ana winds. That cycle stresses fence hardware in a way a lot of installers don’t account for.
- A gate that drags or won’t latch cleanly. The post has settled or the hinge has deformed. In Los Angeles, this is almost always the first sign of a failing post footing – the concrete has cracked or the soil underneath has shifted after a wet season.
- Posts leaning after wind events. Canyon and hillside parcels in Chatsworth, Porter Ranch and the Hollywood Hills see wind loads that a standard 4×4 post in 18 inches of concrete can’t handle. The post itself usually isn’t failing – the footing is.
- Rust bloom at welds and hardware. Powder-coat failure at weld seams is the most common rust point on aluminum fence in Los Angeles, and once it starts, the structural rating of the panel is compromised.
- Pickets or panels loose in the frame. Fasteners back out over repeated thermal expansion. On a rated assembly, this means the panel is no longer functioning as a system.
- Visible concrete failure at the post base. Cracks radiating from the post, or a base plate sitting proud of the surrounding surface, mean the footing has lost its bond. This is the failure that most often surprises owners – the fence looks fine at the top and the whole run is teetering.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Fence installation in Los Angeles runs $4,130 to $10,620 on our standard pricing. That’s the installed number – materials, labor, concrete, cleanup and the workmanship warranty are all in it. We don’t quote parts-and-labor separately and surprise you at invoicing.
What drives the range:
- Linear footage. The single biggest factor. A 100-ft rear fence and a 200-ft perimeter are different jobs.
- Material. Vinyl sits at the lower end. Powder-coated aluminum rated for wind load sits at the upper end.
- Terrain. A fence on a flat lot in Mid-City installs at one price. A fence climbing a canyon slope in Mount Washington takes more posts, more concrete and more labor.
- Gates. Each gate is a separate assembly with its own hardware. A double gate or a driveway swing gate adds meaningfully.
- Permits and utility locates. We handle both. Los Angeles has fence height limits and setback rules that vary by zone, and a fence over a certain height along a property line typically requires a permit. We pull them and pass inspection – that’s part of the scope, not an extra.
Every installation carries the 730-Day Done Right Promise. If it’s not done right, we make it right – in writing, for two full years.
DIY or Call Us?
Here’s the honest split. What you can safely check yourself: walk the fence line and look for leaning posts, rust at welds, loose pickets, gate drag, and cracked concrete at post bases. Taek a photo of any manufacturer label on the post bracket or gate hinge. That’s diagnostic work and it costs nothing.
Where DIY goes wrong on this kind of assembly: replacing a rated panel or gate hardware with a non-rated equivalent, and resetting a post without addressing the footing. The fence is a system. A new panel on a failing footing leans again in one wet season, and a non-rated hinge on a wind-loaded gate fails at the hinge, not the panel. There’s also a real safety component on a tall fence or one climbing a slope – a panel that comes down under wind load can cause serious injury. We’re not going to tell you not to touch your own fence, but we will tell you that a fence rated for Los Angeles wind conditions has to be re-assembled as a rated system or it isn’t rated anymore.
Call (888) 427-1733 and we’ll walk the property with you, quote the realistic scope, and tell you if a repair is all you need.
FAQs
A powder-coated aluminum fence rated for wind load will last 20 to 30 years in most Los Angeles conditions if the footings are set correctly and the hardware is rated to match. The fence panel usually outlasts the hardware, which is why we replace hinges and brackets on any re-install – the part that fails first here is the gate hardware, not the panel. Call (888) 427-1733 for a life-expectancy read on your specific fence.
Often, yes. A single leaning post or a failed gate hinge is a repair – we reset the footing or swap the hardware and the run keeps going. A run of rust at every weld, or multiple posts leaning in the same direction, means the installation is failing as a system and repair isn’t the right answer. We’ll tell you which one you’re looking at. Call (888) 427-1733 to schedule a free assessment.
Most gate hardware replacements and single-post resets are completed in a single visit. A full fence run replacement in Los Angeles typically takes one to three days depending on footage, terrain and whether concrete has to cure before panels go up – we won’t set panels on green concrete just to hit a schedule.
We source from suppliers who can verify the wind-load rating and material spec of each component – not from whichever yard has a pallet of hinges that week. For a rated assembly, the hardware has to match the rating of the panel or the whole system loses its rating. That’s not something we’re willing to shortcut, and we’ll show you the spec sheet on any component that carries a rating before we install it. Call (888) 427-1733 and we’ll walk you through what we’d source for your property.
We install PGT-compatible fence systems – and we also work with KraftMaid, Cambria and Silestone on other parts of the home. If your fence needs a real diagnosis and a written quote, call (888) 427-1733 to schedule a free estimate. Our technicians have up to 12 years of experience, we pull permits and pass inspections, and our pricing is upfront with no surprises.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.