Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Windows & Doors: The Los Angeles Owner’s Guide
We install and service CWS-compatible windows and doors throughout Los Angeles, and most full window replacements here run $5,310 to $17,700 depending on size, glazing and frame material. A single failed component – a balance, a roller, a lock, a sash seal – is often a repair rather than a full swap, and we can usually tell you which within one visit. Owners typically discover the problem slowly: a window that won’t stay up, a door that drags on the sill in August, condensation fogging the glass from the inside, or a lock that needs two hands and a shoulder. CWS made solid products, but parts wear out, and in Los Angeles the sun and the marine layer do the wearing.
Which CWS Models This Applies To
CWS (Custom Window Systems) built a wide range of vinyl and aluminum products over the decades, and the part you need depends on which line your home has. The single most useful step is finding the manufacturer label. On CWS windows it’s usually etched into the top of the upper sash or stuck to the frame in the head jamb; on patio doors, check the door panel edge and the frame header. The label carries the series and a date code, and that date matters because CWS changed balance systems and glazing methods across production runs. A balance from an early run won’t drop into a later sash, and vice versa.
If the label is gone, we identify the part by measurement: sash weight, channel width, pivot bar spacing, and roller diameter. That’s where the OEM-versus-aftermarket decision gets practical. For hard-to-find CWS-specific hardware, a quality aftermarket equivalent from a manufacturer like AmesburyTruth or Roto often fits and performs as well as the original at lower cost. For structural components and glass units, we match the original spec. We’re an independent service provider and not affiliated with CWS, so we source what actually fits your window rather than what’s easiest to order.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CWS Windows & Doors Is Failing
Most CWS failures fall into a handful of patterns, and each points to a specific part:
- The sash won’t stay up. A worn or broken spiral balance or block-and-tackle balance has lost its tension. In Los Angeles, heat cycling on south- and west-facing windows speeds this up, and we see it most on second-story sashes that get direct afternoon sun.
- The door drags or scrapes the sill. Worn rollers, a sagging hinge, or a frame that’s shifted with the soil. Older Los Angeles homes on expansive clay move more than owners expect.
- Fogging or condensation between the panes. The insulated glass unit’s seal has failed, letting moisture into the air space. No amount of cleaning fixes this; the glass unit gets replaced.
- The lock or handle sticks or won’t latch. A worn lock mechanism, a misaligned keeper, or a strike plate that’s shifted. Left alone, a door that won’t latch properly is a security concern, not just an annoyance.
- Drafts, rattles, or water intrusion at the frame. Failed weatherstripping, worn sweeps, or degraded sealant. Coastal Los Angeles homes near the marine layer see this sooner than inland properties.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Los Angeles depends on what’s being replaced and how many units are involved. These ranges reflect the local market:
- Window replacement: $5,310 to $17,700 for a typical multi-window job
- Impact window installation: $9,440 to $29,500, higher because of the glass spec and hardware
- Single component repair (balance, roller, lock, weatherstripping): priced per unit once we’ve identified the part
The range is driven by unit count, glass type, frame material, and whether the opening needs reframing. We give upfront pricing with a written line-item quote – the number you see is the number you pay, no change orders mid-job. All work is covered by our 730-Day Done Right Promise, so if it’s not done right, we make it right. Most single-component swaps are completed in a single visit.
DIY or Call Us?
Some checks are safe and worth doing yourself. Look for the CWS label and write down the series and date code. Measure the sash and note the balance type. Clean and lubricate rollers and locks, and check that weatherstripping isn’t torn. What we don’t recommend is replacing a balance, pulling a sash, or resetting a glass unit on your own. A tensioned balance under load can snap back with real force, and a dropped sash on a second-story window is a genuine hazard. Glass units are heavy and unforgiving, and a misaligned frame lets in water you won’t notice until the drywall stains. If you’re not sure which part failed, call us at (888) 427-1733 and we’ll tell you what we think before anyone comes out.
FAQs
Plan on 15 to 25 years for the window itself, with balances, rollers, locks and weatherstripping wearing out well before that – often in the 8 to 15 year range on sun-exposed elevations. The Los Angeles climate is gentler than most, but UV exposure and the coastal marine layer both shorten seal and hardware life. Call (888) 427-1733 for an assessment on your specific units.
Usually yes. Balances, rollers, locks, sweeps and weatherstripping are replaceable, and a failed glass unit can be swapped without replacing the whole window. Full replacement makes sense when the frame is cracked, the sash is warped beyond adjustment, or multiple components have failed at once. Call (888) 427-1733 and we’ll give you a straight answer on which path fits.
A single balance, roller, lock or weatherstripping job is typically done in one visit, often in under an hour per unit. A glass unit replacement takes a bit longer because of the measurement and seal. Multi-window jobs or full replacements are scheduled and quoted up front. Call (888) 427-1733 to schedule a free estimate.
We identify your series from the manufacturer label or by measurement, then match to OEM or a quality aftermarket equivalent from a maker like AmesburyTruth or Roto. We don’t carry stock or keep parts on a truck – we order what fits your specific unit, which is why the label and measurements matter. Call (888) 427-1733 and we’ll walk you through what we need.
If a CWS window or door in your Los Angeles home is sticking, fogging, sagging or won’t lock, the sooner we look at it the simpler the fix usually is. Our technicians have up to 12 years of experience, we answer the phone with a live person 24/7, and every project is backed by our 730-Day Done Right Promise. We also service KraftMaid, Cambria and Silestone products for homeowners planning a larger remodel. Call (888) 427-1733 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.