Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Ameristar Fence Installation: The Los Angeles Owner’s Guide
Ameristar fence installation in Los Angeles typically runs $4,130 to $10,620 installed, depending on fence height, run length, gate count, and whether we’re setting posts into decomposed granite or clay soil. We install Ameristar-compatible aluminum and steel ornamental fencing across the city, and most residential runs are completed in a single visit with a written, line-item quote before we touch a post hole.
Owners usually discover a failure the same way: a leaning post after a Santa Ana wind event, a gate that drags on the driveway, powder coat flaking along a weld seam, or a picket that rattles in the channel when you close it. That’s the moment the phone comes out. Here’s what we know about matching Ameristar components to your specific fence run, what fails first in Los Angeles conditions, and what the job actually costs.
Which Ameristar Models This Applies To
Ameristar builds ornamental aluminum and steel fencing in residential series (typically 48″, 54″, and 60″ heights) with distinct picket profiles, rail styles, and post caps. The three things that determine which component fits your fence are the series line, the post size, and the rail channel depth. Mixing them is where installations go wrong: a 2″ post cap from one series won’t seat on a 2.5″ post from another, and a rail bracket sized for a specific channel won’t hold tension in a different profile.
The easiest way to identify your fence: measure the post outside diameter with a tape (square posts measure corner-to-corner), photograph the rail-to-post connection from the inside of the fence, and locate the manufacturer tag or stamped mark on the bottom rail or inside a post cap. Ameristar stamps its components. If you can’t find the tag, the photos and measurements usually get us there.
On the OEM-versus-aftermarket question: Ameristar’s own replacement components are the safest match for color and finish consistency, and we source them directly. Quality aftermarket aluminum components exist for rails, brackets, and pickets, but powder coat color matching is where aftermarket falls short, especially on faded fences. A mismatched panel stands out on a Los Angeles street where the sun hits your fence most of the day. We’re an independent installer, not affiliated with Ameristar, so we quote both options honestly and let you decide. We also work with KraftMaid, Cambria, and Silestone on the interior side of the house, but fencing is its own discipline and its own set of brand relationships.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Ameristar Fence Installation Is Failing
- Leaning posts at the base. Usually inadequate footing depth or concrete that was poured into loose, uncompacted soil. In Los Angeles, decomposed granite and expansive clay both shift seasonally, and a post set at 24″ instead of 30″+ will walk.
- Gate sag and drag. Hinge screws backing out of a hollow post, or a gate hung too wide for its frame without a diagonal brace. A gate over 48″ wide needs bracing; many installations skip it.
- Powder coat flaking or chalking. UV degradation along the top rail and picket tops, accelerated by Los Angeles smog and direct sun. Chalking is cosmetic; flaking that exposes bare aluminum is not, because it starts pitting.
- Rattling or loose pickets. The picket retainer or channel screw has worked loose, often from wind vibration or a fence installed without the correct number of fasteners per picket.
- Rust bleeding at welds and cut ends. Ameristar’s finish protects the surface, but field cuts and drilled holes expose raw metal unless they’re touched up. Untreated cuts rust first, usually within a season.
Replacement Cost & What’s Included
Installed Ameristar fence in Los Angeles runs $4,130 to $10,620 for a typical residential run. What drives the range: linear feet, fence height (48″ to 60″ adds material and labor), number of gates, footing difficulty, and whether we’re removing an existing fence. A single gate adds meaningful cost because gate fabrication, hinges, and a heavier post are separate line items.
Every quote is line-item: materials, labor, footings, haul-away, and any permit or HOA submission required. We pull permits where the city requires them and we don’t change the number mid-job. Pricing is upfront, no surprises, and all work is covered by our 730-Day Done Right Promise. If a post leans or a weld fails inside that window, we come back and make it right. That’s the whole point of putting a guarantee in writing.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Here’s the honest split. You can safely measure your fence, photograph the rail connections, check post caps for the manufacturer stamp, and tighten exposed gate hinge screws with a screwdriver. That’s diagnostic territory and it’s useful.
Where DIY goes wrong with Ameristar fencing: setting posts. Footing depth, concrete mix, soil compaction, and plumb are the difference between a fence that stands for 20 years and one that leans after the first wet winter. Digging into a slope or near a property line also raises utility locate and code questions that are easy to get wrong. Pulling a gate frame apart to replace a hinge or brace requires the right fasteners and alignment, and a gate that’s off by a quarter inch won’t latch. Most of what we see on DIY fencing calls is a post problem dressed up as a part problem. Call (888) 427-1733 and we’ll tell you straight whether you need a part or a footing.
FAQs
Ameristar aluminum and steel fencing typically lasts 20 to 30 years in Los Angeles conditions, with the finish being the limiting factor rather than the metal. Direct UV, smog, and salt air near the coast accelerate powder coat chalking; the structural aluminum outlasts the coating. Call (888) 427-1733 for an inspection if your fence is past 15 years and showing finish wear.
Yes, often. Single pickets, rails, post caps, and gate hardware can be replaced without tearing out the whole run, as long as the section is still plumb and the footings are sound. If posts are leaning or the footing has failed, repair is a patch on a bigger problem. Call (888) 427-1733 and we’ll tell you which you’re looking at.
Most residential Ameristar installs are completed in a single day once materials are on site, with larger runs or gate fabrications running into a second day. Repairs are usually a half-day. Lead time depends on sourcing the specific series components. Call (888) 427-1733 for a scheduling estimate.
We identify the series from your measurements, photos, and any manufacturer stamp, then source OEM components through Ameristar’s supply chain or a quality aftermarket match if the OEM line is discontinued. We don’t guess on color or profile; we confirm before ordering. Call (888) 427-1733 to start the identification.
Get a Written Quote Before You Commit
A fence that’s failing is a problem you can solve with one call. We’ll measure the run, identify the components, and hand you a line-item quote with the full range in writing, backed by the 730-Day Done Right Promise and upfront pricing that doesn’t move. Our technicians have up to 12 years of experience and arrive background-checked and in uniform. Call (888) 427-1733 to schedule your free estimate. Live person, 24/7, no voicemail.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.