Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Quikrete Driveway & Pavers: The Los Angeles Owner’s Guide
We install Quikrete-compatible driveways and paver systems throughout Los Angeles, and most full paver driveways land between $8,260 and $21,240 installed; concrete driveways typically run $5,310 to $14,160. When a hardscape “part” fails, it’s almost never the material itself. It’s what sits under and between it. Owners usually spot the problem the same way: a paver that rocks when they step on it, sand washing into the gutter after a rain, or a joint that keeps opening no matter how many times it’s refilled. In Los Angeles, clay soils and dry summers followed by winter rain push movement faster than most people expect.
Which Quikrete Models This Applies To
Quikrete isn’t a “model number” product line the way a garage door opener is. It’s a family of bagged materials, and the driveway and paver side breaks into a few clear buckets: paver joint sand (including polymeric sand that hardens in the joint), concrete mixes for slabs and footings, and patching and resurfacing products for existing concrete. The label on the bag tells you exactly which one you’re dealing with, and the bag’s coverage chart – usually printed in square feet at a given joint width – is the number that matters. Watch the compatibility gotcha here: polymeric joint sand needs a dry joint and the right width to lock in. Fill a wide, unstable joint and it cracks and washes out, and it can stain pavers if it’s over-watered during activation. Quality aftermarket joint sand and paver base materials are perfectly legitimate when the spec matches; skimped base is where jobs fail regardless of brand. If you’re weighing Quikrete against other product lines, we also work with KraftMaid, Cambria and Silestone on the interior side. Groundwork Construction Co. of Los Angeles is an independent service provider and isn’t affiliated with Quikrete.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Quikrete Driveway & Pavers Is Failing
- Joint sand washing out after rain. Water is getting under the pavers because the joint never locked or the base holds moisture. In Los Angeles, that shows up fast after the first real winter storm.
- Pavers that rock or sink at the corners. The base layer was too thin or not compacted, and the paver is now bridging a void. Left alone, neighbor pavers migrate toward the dip.
- Weeds sprouting from joints every season. Missing or degraded joint sand leaves a seed bed. It’s a symptom of joint failure, not a weed problem.
- Cracking and spalling on a concrete slab. Clay soil movement, tree roots, or a pour that was too thin. Los Angeles slabs on expansive soil are prone to hairline cracks that widen with every dry-wet cycle.
- Standing water or puddling on the drive. The slope was never set right, or the surface has settled. Water sitting on pavers or concrete breaks down the material and the base underneath.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed paver driveway work in Los Angeles runs $8,260 to $21,240 depending on square footage, paver type, base depth and how much existing material has to come out. Concrete driveways run $5,310 to $14,160, and full driveway replacement, including tear-out and hauling, lands at $5,900 to $16,520. Resealing an existing surface runs $295 to $825. The range is driven mostly by base prep and drainage, not the surface material. A straight swap of joint sand on a healthy base sits near the low end; rebuilding a failed base doubles it. We quote parts and labor as line items and put the number in writing before work starts. Every job carries the 730-Day Done Right Promise, so the work is backed in writing.
DIY or Call Us?
You can safely check a few things yourself: pull a loose paver and look at the base depth, sweep a joint to see if the sand is loose or hardened, and watch where water runs during a rain. That’s inspection, not repair. Where DIY goes wrong on pavers and concrete is the base and the compaction. Re-sanding joints over a soft base hides the problem for a season and then it returns worse. Replacing a section of concrete slab without cutting clean control joints or matching the base creates a cold joint that cracks within a year. We do the tear-out, base prep, compaction and finish so it holds. Call (888) 427-1733 to schedule a free estimate.
FAQs
Properly installed polymeric sand typically holds three to five years in Los Angeles, and it fails faster if the base moves or water runs into the joints. Our technicians have up to 12 years of experience with these systems. Call (888) 427-1733 for an exact quote – estimates are free.
Often, yes. If the pavers themselves are intact and the base is sound, re-sanding joints and re-leveling a few units is far cheaper than replacement. The base has to be stable for that to work. Call (888) 427-1733 and we’ll tell you straight which one you need.
A joint re-sand on a normal driveway is usually a single visit, while a base rebuild or replacement runs several days because of tear-out, base prep and cure time. Most jobs are completed in a single visit when the base is sound. Call (888) 427-1733 for a realistic timeline.
We buy the specified Quikrete product directly from local suppliers to match your joint width, base spec and surface finish, and we confirm compatibility before the job. We don’t claim to stock or carry parts on a truck. Call (888) 427-1733 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.