Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Windows & Doors: The Los Angeles Owner’s Guide
We install and service Dvele-compatible windows and doors across Los Angeles, and a typical single window replacement runs $5,310 to $17,700 installed, while impact-rated units land at $9,440 to $29,500. We’re an independent service provider, not affiliated with Dvele, so we match the part to your model and quote the work straight. Most owners find us after a symptom they can’t ignore any longer: a slider that won’t latch in the frame on a hot afternoon, fog between the panes, or a door that suddenly needs a shoulder to close.
Which Dvele Models This Applies To
Dvele builds prefab modular homes, and the window and door packages vary by plan and by the year the module was built. That means the part you need is tied to the unit, not to a single universal Dvele spec. The fast way to identify what you have is the manufacturer’s label etched in the corner of the glass or stamped on the sash edge, plus the rough opening dimensions you can measure yourself with a tape. Measure width and height at three points in each direction; if they disagree by more than a quarter inch, you’re looking at a frame issue rather than a simple part swap.
On the OEM-versus-aftermarket call, Dvele-specific hardware and glazing are often available but slow, and pricing reflects that; a quality aftermarket equivalent from a major window brand usually installs faster and carries comparable performance when the specs line up. We walk that decision with you instead of defaulting to the expensive path. Some Los Angeles homeowners come to us through our work with KraftMaid, Cambria, and Silestone kitchens and end up asking about a window while we’re there; we handle both on the same schedule.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Dvele Windows & Doors Is Failing
- Fogging or condensation between the panes. The sealed glass unit has lost its seal and moisture is trapped inside; the glass itself has to be replaced, not just cleaned.
- Drafts or a hot spot near the window in summer. Weatherstripping has flattened or the sash is no longer sitting square, letting Los Angeles heat and valley dust push through.
- Sticking or dragging sliders and doors. Rollers wear and tracks fill with grit; sometimes it’s a failing hinge, sometimes the whole unit has shifted and needs re-anchoring.
- Water staining or soft wood at the sill. Seals have failed and moisture is getting behind the frame, a common sight after a wet winter in Los Angeles.
- A latch that won’t catch or a lock that won’t turn. The hardware is worn or misaligned, and on an exterior door that’s a security gap, not just an annoyance.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed prices depend on unit size, glazing, and whether we’re swapping a single sash or a full window. Here’s how it breaks down for Los Angeles homes:
- Standard window replacement: $5,310 to $17,700 installed
- Impact-rated window installation: $9,440 to $29,500 installed
- Door hardware, glass, or single-sash swaps: priced per part, quoted line by line
What drives the range: glass type, frame material, impact rating, and how much of the surrounding frame has to come out. We put the parts cost and the labor on the same written quote so you see exactly what you’re paying for. Every window and door job is backed by our 730-Day Done Right Promise, and we stand behind the work in writing, not just in conversation.
DIY or Call Us?
You can safely check a few things yourself: measure the opening, read the glass label, test the latch by hand, and look for staining or soft spots around the frame. Where DIY goes wrong on windows and doors is the install itself. A sealed glass unit can’t be resealed at home, and a mis-hung door or window lets water in behind the frame, which is how a small part failure turns into a rot repair. If your unit is high up, on a second story, or the frame is already showing water damage, call us. Reach a live person at (888) 427-1733 any time and we’ll quote it at no cost.
FAQs
Expect a quality window unit to hold for roughly 20 to 25 years, with hardware like rollers and latches wearing out sooner, often within 10. In Los Angeles, sun exposure on south- and west-facing glass shortens seal life compared with shaded units, so those are the first to fog.
Sometimes, yes. A worn roller, hinge, or latch can usually be swapped without replacing the whole unit, which costs far less. A fogged glass unit or a frame with water damage needs the glass or the unit replaced; we’ll tell you honestly which you’re facing. Call (888) 427-1733 for a free look.
A single window or door swap is typically a one-visit job; a multi-unit replacement across a home usually runs two to three days depending on count and access. We confirm the schedule in your written quote so there are no surprises.
We identify your unit from the glass label and measurements, then source the matching OEM part or a verified equivalent from a major brand. We don’t keep parts on a truck; each part is ordered to your unit, then installed and checked on site. Estimates are free, so call to get started.
Call (888) 427-1733 to schedule your free estimate on your Dvele windows and doors. We answer with a live person, day or night, and you’ll get upfront pricing with the number we quote being the number you pay. From foundation to finish line, one contractor handles it, backed by our 730-Day Done Right Promise.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.