Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Windows & Doors: The Los Angeles Owner’s Guide
We install Boral-compatible windows and doors across Los Angeles, and full window replacement here typically runs $5,310 to $17,700 installed, with impact-rated units at $9,440 to $29,500. Most owners don’t wake up thinking about parts. They notice it slowly: a door that drags on the jamb in August, a window that fogs between the panes and never clears, or a lock that suddenly needs two hands and a shoulder to seat. That’s the moment the part hunt starts, and it’s usually where the good information runs out.
Which Boral Models This Applies To
Boral’s window and door catalog spans a few lines, and the part you need depends entirely on which one is hanging in your wall. Vinyl new-construction and replacement units, aluminum-clad products, and the door slab lines don’t share hardware, weatherstripping, or glazing gaskets. A sash balance from one line won’t drop into another, and we’ve seen Los Angeles homeowners order the right-looking part three times before measuring the pivot bar on the original.
Start at the unit itself. Look for a manufacturer label on the top or side of the sash, inside the head jamb of a slider, or on the hinge edge of a door slab. That label carries the series and often the glass package. If it’s gone or painted over, measure instead: sash width and height to the nearest 1/16 inch, glass thickness, and the balance channel length. Those four numbers do more for a correct match than any photo.
The OEM-versus-aftermarket call matters here. Boral factory parts are the safe bet for anything structural or under warranty, but common wear items like sash balances, tilt latches, and screen corners have solid aftermarket equivalents that fit the same channel dimensions. For Los Angeles, the practical complication is salt air near the coast: aluminum and steel hardware pit faster in Santa Monica and Redondo Beach than they do in Pasadena, so we lean toward stainless or polymer equivalents on replacements even when the original wasn’t.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Windows & Doors Is Failing
Most failures fall into five patterns. Here’s what each symptom usually means:
- The sash won’t stay up. A worn or snapped sash balance, or a broken balance shoe at the bottom of the channel. Vinyl sashes are heavy and the balance takes the load, so a failing one lets the window drift shut or slam.
- Fog or condensation trapped inside the glass. That’s a failed seal in the insulated glass unit, not a foggy room. Once the desiccant is saturated the haze stays put and the unit’s insulating value drops with it.
- The door drags, sticks, or won’t latch. Usually a sagging hinge, a worn roller on a slider, or a strike plate that has shifted as the frame moved with the seasons. In older Los Angeles homes, settled framing is a common contributor.
- Water staining or soft spots at the sill. Failed weatherstripping, a cracked glazing gasket, or a sill pan that was never sloped right. This one gets expensive if ignored, because the water reaches the framing behind the wall.
- The lock or handle feels loose or gritty. Internal hardware wear, or corrosion from coastal air. A handle that won’t fully engage is a security problem, not just an annoyance.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Los Angeles, window replacement runs $5,310 to $17,700 for a standard project, and impact window installation runs $9,440 to $29,500 where the unit is rated for it. A single hardware or balance repair sits far below those figures, and we quote it line by line before anyone touches the frame.
| Scope | Installed Range (Los Angeles) |
|---|---|
| Hardware, balance, or weatherstrip repair | Quoted per unit, usually a small fraction of full replacement |
| Window replacement (standard) | $5,310 – $17,700 |
| Impact window installation | $9,440 – $29,500 |
What moves the number: unit count and size, whether the frame is sound enough for a pocket replacement or needs a full-frame tear-out, glass package and impact rating, and finish. Parts plus labor are itemized so you see what the part costs and what the install costs. Every job carries our 730-Day Done Right Promise, and the number you see on the quote is the number you pay.
DIY or Call Us?
Some things are safe to check yourself. You can measure the sash, photograph the label, test whether the glass haze is inside the unit or on the surface, and confirm the frame is square with a level. You can also swap a screen corner or a loose handle if the screws are accessible and the frame is intact.
Where it goes wrong: insulated glass units are sealed at the factory and can’t be re-gasketed in place, so a fogged window is a replacement, not a repair. And anything requiring you to remove a sash from its track on an upper floor puts you on a ladder at height, which is where we see injuries. We don’t recommend it. A background-checked, uniformed technician handles the removal, the part match, and the reseal, and most single-unit hardware jobs are done in one visit. Call (888) 427-1733 and we’ll tell you honestly whether you need a part or a whole unit before you spend a dollar.
FAQs
A well-installed Boral window typically holds its seals and hardware for 15 to 25 years, and doors in the 20-year range with normal care. In Los Angeles, coastal salt air and inland UV both shorten hardware life, so we often see locks and balances fail years before the glass or frame does. Call (888) 427-1733 for a free assessment if yours are past that mark.
Often yes. Balances, latches, rollers, and weatherstripping are all replaceable on their own, and that’s the cheaper route when the frame and glass are sound. A fogged insulated glass unit is the exception, since the seal can’t be restored in the field. We’ll tell you which one you’re facing on the first visit.
A single hardware or balance replacement is usually a same-visit job of an hour or two. A full window or door unit replacement takes longer, and we schedule it as a planned project with a clear timeline rather than a rushed call-out. Call (888) 427-1733 to get a realistic date and quote.
We match to your unit’s series and measured dimensions, then confirm OEM or a verified aftermarket equivalent before ordering. We don’t claim to stock Boral parts or carry them on a truck, so we source per job and tell you the lead time upfront. That honest sourcing is what keeps the part fitting the first time.
Groundwork Construction Co. of Los Angeles is an independent service provider and is not affiliated with Boral. We also work with KraftMaid, Cambria, and Silestone on other parts of the home.
Whether it’s one stubborn window or a whole-house door and window project, we quote it upfront, back it in writing, and answer the phone with a live person 24/7. Financing at 0% for 18 months is available, and projects over $10,000 get $1,000 off. Call (888) 427-1733 for your free estimate.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.