Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mighty Buildings Driveway & Pavers: The Los Angeles Owner’s Guide
We install Mighty Buildings-compatible driveway and paver systems across Los Angeles, with paver driveway installation typically running $8,260 – $21,240 and concrete driveway work at $5,310 – $14,160 depending on square footage, base prep and paver selection. Patching and sealing visits can often be scheduled the same day for smaller repairs. Most owners discover a failure the same way: a paver edge lifts after a rainy season and rocks underfoot, a hairline crack in the slab spreads across a full panel, or water starts pooling against the foundation where it never used to. By the time a paver shifts an inch or two, the base beneath it has usually been moving for months, and that is the part of the problem you can’t see.
Which Mighty Buildings Models This Applies To
Mighty Buildings builds factory-finished panels and modules, and their driveway and hardscape packages are specified around the exact panel footprint, slab elevation and finish grade of each model line. That means the paver type, edge restraint, base depth and drainage pitch called out for one of their single-story configurations does not automatically carry over to a two-story or ADU layout, even when the finished look is identical. The compatibility gotcha most Los Angeles owners run into: Mighty Buildings’ panelized foundations and step-down thresholds can sit lower or higher than a conventional stem wall by a few inches, so an off-the-shelf paver course or standard concrete thickness that works on a stick-built house may not meet the finished floor height cleanly.
To identify the right system, climb into the records before the yard. The panel or module serial label is typically affixed near the utility chase or on the exterior wall inside the access panel, and the hardscape spec sheet in your owner packet lists the paver series, base aggregate and edge restraint by model revision. When that paperwork is missing, we measure the existing paver thickness, joint width and base depth in place and match the OEM or a quality aftermarket equivalent to the original spec range. We’re an independent service provider, not affiliated with Mighty Buildings, and our technicians have up to 12 years of experience matching hardscape to panel-built homes. Need something closer to the original? OEM parts take longer to source. A compatible aftermarket paver or slab spec installed correctly usually performs the same, gets you a working driveway sooner, and costs less.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Mighty Buildings Driveway & Pavers Is Failing
Look for these five symptoms on any panel-built driveway in Los Angeles. Each one points to a cause below the surface:
- Pavers rocking or lifting at the edge. Water has worked into the bedding layer and the base aggregate has shifted. It gets worse every rainy season.
- Hairline cracks spreading across a concrete panel. Usually a sign the subgrade settled unevenly beneath the slab, not just surface wear.
- Pooling water against the panel foundation. The slope has flattened over time or the drainage pitch was off from the start. Standing water near the foundation is a problem for the whole structure.
- Joint sand washing out and weeds in the seams. The joint sand has eroded and the paver system is losing its interlock, which lets water in faster.
- Heaved or frost-affected pavers after a wet winter. In Los Angeles this is less about frost and more about saturated base after heavy storms. Once the base stays wet, it won’t drain properly and the pavers move.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing runs a wide range depending on how much base work is needed. Here’s how Los Angeles projects typically land:
| Service | Typical Installed Price |
|---|---|
| Paver driveway installation | $8,260 – $21,240 |
| Concrete driveway installation | $5,310 – $14,160 |
| Asphalt driveway paving | $4,130 – $10,620 |
| Driveway replacement | $5,900 – $16,520 |
| Driveway sealing | $295 – $825 |
The low end is a straight paver or slab replacement over sound base. The high end means real base work: excavation, new aggregate, edge restraint and drainage correction. Replacement pricing includes removal and disposal, base preparation, materials and installation. That’s parts and labor in one number. Call (888) 427-1733 for a free, written quote. Every project carries our 730-Day Done Right Promise, and 0% financing for 18 months with $1,000 off projects over $10,000 is available.
DIY or Call Us?
What you can safely check on your own: measure paver thickness and joint width, photograph cracks and pooling areas, and confirm the panel serial number for the part match. What tends to go wrong: base repair. Swapping pavers without fixing the aggregate underneath just resets the clock, and water will find the same gap in six months. Concrete replacement is heavier, harder and more dangerous to handle than most owners expect, and it’s easy to get the finished grade wrong, which sends runoff toward the foundation. That’s a structure problem, not a driveway problem. When the ground under a panel-built home is involved, base and drainage matter more than the surface material. Call (888) 427-1733 for a free estimate before you rent a tool or order a single pallet.
FAQs
A properly installed paver system over a stable base lasts 25 – 50 years; concrete slabs typically run 20 – 30 years before major failure. In Los Angeles conditions, the base prep and drainage do most of the work to get you there. Call (888) 427-1733 to assess yours.
Often yes. When the failure is at the surface (joint sand, a few lifted pavers, edge pieces), a focused repair usually works. If the problem is base failure or widespread cracking, replacement is the only reliable fix. Full assessment tells you the answer. Call (888) 427-1733 for a free estimate.
A focused repair is typically a one-day job. Full paver or concrete driveway replacement generally takes two to five days depending on square footage, base work and curing time. Call (888) 427-1733 to get a timeline for your specific site.
We work from your model’s hardscape spec sheet when available, then measure existing paver series, base depth and edge restraint in place to lock the match. OEM or a compatible aftermarket equivalent, both can work when the base is right. Call (888) 427-1733 to get started.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.