Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Fence Installation: The Los Angeles Owner’s Guide
Schluter fence installation in Los Angeles typically runs $4,130 to $10,620 installed, depending on footage, terrain, and the condition of what’s being replaced. We install Schluter-compatible systems and book free on-site estimates on your schedule, not weeks out. Most owners come to us after a fence that looked fine in year one starts leaning, loosening at the posts, or showing rust bleed along the bases after a wet winter – the hardware and footings fail long before the panels do.
Which Schluter Models This Applies To
Schluter’s fence and exterior profile lines have changed part numbers more than once, and that’s where most ordering mistakes happen. The series code stamped on the inside of the panel rail or on the post cap tells you which generation of hardware you have. Match by that code and by measured panel width – not by the label on the box at the home center, which is often for a different series.
Two practical gotchas we see in Los Angeles:
- Panel width drift: a nominal 6-foot panel can measure anywhere from 70 to 73 inches across Schluter series. Measure the actual opening, not the old panel’s label.
- Finishes that don’t match part numbers: the same hardware part can ship in several finish codes, and mixing them shows up as a color seam along the rail line after a season of sun.
On the OEM-versus-aftermarket call: for structural pieces like post anchors and rail brackets, we use genuine Schluter parts. For non-structural caps and trim, a quality equivalent works fine and costs less. We don’t claim to stock parts and we don’t carry them on a truck – each job is sourced to your series.
Groundwork Construction Co. of Los Angeles is an independent service provider, not affiliated with Schluter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Fence Installation Is Failing
- Posts leaning after rain: soil settlement around the footing. In Los Angeles, our clay-heavy soils expand and contract hard with seasonal moisture, and a shallow footing will move.
- Loose or stripped rail brackets: fastener corrosion or under-torqued hardware. Once one bracket loosens, the load shifts to its neighbors and the whole run works itself loose.
- Rust streaks at the base plate: finish wear exposing bare metal to coastal air and irrigation overspray. This is the fastest failure point on exposed hardware.
- Wobbly gate and sagging hinge side: hinge post movement, not a bad hinge. Replacing the hinge alone won’t fix it.
- Panels out of plumb or rattling in wind: the rail-to-post connection has loosened or panels were cut short and shimmed. Shimmed panels fail within a season or two.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed Schluter fence work in Los Angeles lands in the $4,130 to $10,620 range. Here’s what drives it:
| Item | Typical Range |
|---|---|
| Hardware and parts (brackets, anchors, caps) | $300 – $1,200 |
| Footing repair or replacement per post | $150 – $450 |
| Panel replacement per section | $250 – $700 |
| Labor (removal, reset, install) | $2,000 – $6,000 |
| Total installed | $4,130 – $10,620 |
You get a written line-item quote up front: parts, labor, and disposal listed separately. Upfront pricing, no surprises. Every job carries our 730-Day Done Right Promise – if it’s not done right, we make it right. Live person, 24/7, if you have a question mid-job.
DIY or Call Us?
Safe to check yourself: measure the panel and series code, note which posts lean, and photograph the failed hardware. That’s useful information.
Where DIY goes wrong: resetting footings in our clay soil, retensioning a run that’s already shifted, and matching series hardware. A fence isn’t high-tension wiring or a gas line, but a footing set wrong will lean again within a season – and you’ll have paid twice. For anything beyond a single bracket, call us. We’ll give you a straight assessment: repair versus replace. Call (888) 427-1733 for a free estimate.
FAQs
With proper footings and genuine hardware, expect 15 to 20 years on the structure. Sun exposure and coastal air shorten hardware life first – we see finish wear on exposed brackets in 7 to 10 years near the coast. Call (888) 427-1733 for an assessment of your specific setup.
Often yes. If posts and panels are sound and only hardware or one footing has failed, a targeted repair runs far less than a full replacement. We tell you honestly which way it goes. Call (888) 427-1733 for a free estimate.
Most repairs and hardware swaps are done in a single visit. Full section or run replacements typically take one to three days depending on footage and footing work. We confirm the schedule in your written quote.
We match your series code and measured width to the correct current part number, then source genuine or quality-equivalent parts to that spec – not to a generic box label. That’s how we avoid the fit problems that come from cross-series ordering. Call (888) 427-1733 to get your part matched.
We also service KraftMaid, Cambria, and Silestone products on other jobs.
Call (888) 427-1733 to schedule your free estimate – live person, 24/7, no voicemail. $1,000 off projects over $10,000, and 0% financing for 18 months available.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.