Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Los Angeles Owner’s Guide
If you’re planning a Schluter-system home addition or ADU in Los Angeles, you’re typically looking at $53,100 to $153,400 installed for an addition, and $106,200 to $259,600 for a full ADU build. Schluter products themselves are waterproofing, uncoupling, and edge-profile systems, not the thing that “fails” in a wall or floor the way a mechanical part does; what fails is the installation underneath or around them. Homeowners usually discover the problem months after move-in, when a grout line in a new bathroom cracks, a tile edge lifts, or a shower pan in the new suite starts leaking into the framing below. That’s when they start searching for answers about the Schluter layer they paid for.
Which Schluter Models This Applies To
Schluter makes a family of systems, and the one that matters depends on what part of the addition it’s protecting. Ditra is the uncoupling membrane for tile floors; Kerdi is the waterproofing membrane for showers and wet areas; Schluter-SHOWER is the complete shower assembly with presloped pans and drains; Kerdi-Board is the foam backer board that replaces cement board; Ditra-Heat combines uncoupling with radiant heat; and the profiles (Schiene, Reno-U, Quadec) handle tile-to-floor transitions and edges. Identifying what you have starts with the printed roll edge or board face: Ditra and Kerdi both carry their name and a batch code printed directly on the fleece or membrane surface, and Kerdi-Board is stamped on the back.
Here’s where the OEM-versus-aftermarket call gets different than with mechanical parts. For Schluter, there is no meaningful “aftermarket equivalent” worth using in a wet area. Off-brand uncoupling membranes and liquid waterproofers exist, but they don’t carry Schluter’s system warranty, and mixing brands across a shower assembly is the single most common reason a warranty claim gets denied. If your tile is lifting because the wrong thinset was used over Ditra, the fix is redoing the affected field with the right mortar and membrane, not swapping in a cheaper substitute. Groundwork Construction Co. of Los Angeles is an independent service provider and is not affiliated with Schluter, so we install to the manufacturer’s spec and can’t process Schluter’s own warranty on your behalf.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
The symptoms below are what we actually find when we’re called to an addition or ADU where the tile or waterproofing is misbehaving. Each one points to a specific cause, and most trace back to installation rather than the Schluter product itself.
- Hollow or loose tile over the floor. A dull “thud” when you tap a tile usually means the thinset didn’t bond to the Ditra fleece, often from too-dry mortar or traffic before cure. In a Los Angeles addition with a slab foundation, we also see this where slab moisture wasn’t addressed before the membrane went down.
- Cracked grout in straight lines. Grout that cracks in a grid pattern over a new floor points to movement the uncoupling membrane was supposed to absorb but couldn’t, typically because it was installed over a control joint or with insufficient mortar coverage.
- Water staining or soft drywall below a new shower. This is a Kerdi failure, and it’s the one we take most seriously. A missed overlap at a corner or a fastener driven through the membrane without a seal creates a slow leak that shows up as a stain on the ceiling below or a musty smell behind the wall.
- Lipped tile edges at a Schluter profile. Profile trim that sits proud or won’t sit flush with the tile means the substrate wasn’t flat or the profile was set before the tile layout was checked. It’s cosmetic until it catches a toe or a vacuum, then it’s a trip edge.
- Grout discoloration that keeps returning in a wet area. Efflorescence or dark grout at the shower floor often means water is getting under the tile and finding no correct path to the drain, which traces back to a Schluter-SHOWER pan set without proper slope or a drain flange that wasn’t sealed.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
There’s no meaningful “one part” price here because Schluter failures are installation-scope repairs, and the cost to correct them sits inside the whole addition range. For a Los Angeles home addition, expect $53,100 to $153,400 installed. A full ADU build runs $106,200 to $259,600, and a garage conversion lands at $35,400 to $94,400. Those numbers are the honest range for the whole build, not for a single fix.
What you’re actually paying for on a repair is reactive work: removing the failed tile, assessing how far the moisture traveled, replacing membrane and substrate in the affected field, then reinstalling tile and profile to spec. The range is driven by square footage affected, whether framing or drywall is wet enough to replace, and whether the failed area is a simple floor or a full shower assembly. We price work upfront with a written line-item scope, so the number you see is the number you pay, and the work carries our 730-Day Done Right Promise.
DIY or Call Us?
You can safely do a few things before calling. Tap-set the floor with a screwdriver handle to map hollow tiles, look for stains on ceilings below bathrooms, and check that your profile transitions sit flush. Photograph anything you find; it helps us scope the repair.
Where DIY goes wrong is the repair itself. Schluter waterproofing depends on precise overlaps, the correct unmodified thinset, and a continuous membrane with zero fastener penetrations. A shower that looks right and leaks for a year before it shows damage is a real and expensive outcome we see in Los Angeles, where a slow leak into framing can go unnoticed for months in a warm, dry climate. If water is reaching framing, drywall, or a slab edge, stop and call a professional. Reach us at (888) 427-1733 for a free estimate and we’ll tell you honestly how far the repair needs to go.
FAQs
How long does Schluter waterproofing actually last? Properly installed Schluter membranes routinely hold up decades, but lifespan depends almost entirely on the install, not the sheet itself. Failures we see trace back to skipped corners, wrong thinset, or penetrations, and those show up within the first few years, not at year twenty. Call (888) 427-1733 for an honest assessment of your specific install.
Can a failed Schluter area be repaired instead of torn out? Sometimes, and it depends on how far the moisture traveled. A single hollow tile or a cracked profile can often be spot-repaired; a leaking Kerdi shower usually means removing the affected wall or pan to get back to a clean substrate. We’ll tell you which one you’re looking at after we inspect it, and the estimate is free.
How long does a repair take? A spot profile or tile repair is often a single-visit job, while a shower membrane correction typically runs several days because the substrate has to dry and the new membrane has to cure before tile goes back down. We give you the timeline in writing before we start.
How do you source Schluter products for a repair? We specify the correct Schluter system and matching thinset for your application and order from authorized suppliers so the materials are what the spec calls for. We don’t claim to stock parts or carry them on a truck; each repair gets the right product ordered for the job. For the material selections around the tile, we also install KraftMaid, Cambria, and Silestone, so the whole addition comes together under one scope.
If you’re in Los Angeles and dealing with a failed Schluter installation in a new addition or ADU, the best next step is a free, no-pressure estimate. Groundwork Construction Co. of Los Angeles answers the phone with a live person 24/7, prices the work upfront, and backs it with the 730-Day Done Right Promise. We also offer $1,000 off projects over $10,000 and 0% financing for 18 months so a larger correction doesn’t have to wait. Call (888) 427-1733 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.