Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Kitchen Remodeling: The Los Angeles Owner’s Guide
If your Schluter-bonded tile, shower tray, or uncoupling membrane is lifting, cracking, or letting water behind it in a Los Angeles kitchen, we replace and reinstall the affected system. Full kitchen remodels using Schluter products typically run $16,520 – $53,100 installed in Los Angeles, with targeted repairs costing far less. Parts and system installs are scheduled, not same-day, because proper Schluter work needs the substrate to cure before tile goes down.
Most owners discover a failed Schluter system the same way: a tile feels loose underfoot, a grout joint keeps cracking no matter how many times it’s patched, or a dark line appears at the baseboard after a dishwasher leak. In Los Angeles, where slab-on-grade homes are common and seasonal movement is real, these symptoms show up faster than most people expect. By the time a tile lifts, the membrane underneath has usually been compromised for months.
Which Schluter Models This Applies To
“Schluter” isn’t one product – it’s a family of systems, and the right replacement part depends entirely on which one you have. The common ones in Los Angeles kitchens are DITRA and DITRA-HEAT uncoupling membranes under tile, KERDI waterproofing for wet zones and backsplash runs, KERDI-BOARD foam building panels, and DITRA-HEAT thermostat and heating-cable components. If your kitchen has a tiled shower or a wet sink wall, you may have more than one system in play.
To identify what you have, pull up a loose tile corner (carefully) if one is already lifting, or check the original installer’s paperwork for the material list. Schluter prints the product name on the membrane fleece and on box labels. Measure the stud spacing and substrate thickness before ordering, because DITRA and KERDI-BOARD come in several thicknesses and widths, and using the wrong one is the most common compatibility mistake we see.
On the OEM-versus-aftermarket question: for Schluter specifically, there is no true “OEM equivalent.” The brand’s uncoupling and waterproofing profiles are engineered as a matched system with its own thinset and banding requirements, and mixing in a generic membrane roll defeats the purpose. We source genuine Schluter parts through authorized suppliers. For finishes on top, we also work with KraftMaid cabinets, Cambria and Silestone counters, and the standard tile brands – but the waterproofing layer stays Schluter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Kitchen Remodeling Is Failing
- Hollow-sounding tile: tap a tile with a coin and listen. A dull thud means the bond to the membrane or substrate has failed, usually from moisture intrusion or a missed mortar coverage point.
- Recurring grout cracks: if a crack keeps returning to the same joint, the substrate is moving and the uncoupling membrane is either missing, wrong thickness, or unbonded in that area.
- Lifted or popped tiles at the edge: tiles near a doorway or cabinet run lifting is a classic sign the membrane perimeter wasn’t properly anchored.
- Dark streaks near baseboards or under appliances: a slow leak trapped behind KERDI or under DITRA shows up as staining, musty smell, or bubbling paint on an adjacent wall.
- Cold spots or dead zones with DITRA-HEAT: a heating mat that won’t warm evenly points to a damaged cable or a thermostat that lost its floor sensor reading.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for Schluter kitchen work in Los Angeles depends on how much has to come up and how far the waterproofing runs. Our published ranges:
| Scope | Installed Range (Los Angeles) |
|---|---|
| Full kitchen remodel (Schluter underlayment + tile) | $16,520 – $53,100 |
| Small kitchen remodel | $10,620 – $23,600 |
| Backsplash installation with KERDI | $945 – $2,950 |
| Countertop installation | $2,360 – $7,670 |
| Cabinet installation | $4,720 – $15,340 |
The range is driven by square footage, whether the substrate needs repair, whether there’s a wet wall or shower to re-waterproof, and finish choices. You get a written line-item quote before work starts, and the number on that quote is the number you pay. Every install is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. We also pull the permits and pass the inspections required for Los Angeles residential work.
DIY or Call Us?
Some checks are safe and worth doing yourself: tapping tile for hollow spots, photographing the problem for your records, and reading the labels on your existing membrane and thermostat. Anything past that – removing bonded tile, cutting out a failed KERDI section, or chasing a DITRA-HEAT cable fault – is where homeowners get into real trouble. A compromised waterproofing layer you can’t see hides behind that tile, and a patch that skips the proper banding and thinset just fails again in a few months, this time with more damage underneath.
If there’s any chance of a live electrical issue with a heating system, treat it as a professional job. Turn off the breaker and leave it alone until a trained tech inspects it.
Call (888) 427-1733 for a free estimate. A live person answers 24/7, no voicemail, and we’ll tell you honestly whether you’re looking at a repair or a reinstall.
FAQs
A properly installed Schluter membrane system should last 25+ years, but in Los Angeles the weak point is usually moisture intrusion behind tile, not the membrane itself – one untreated leak can cut that timeline drastically.
Sometimes, yes. A single lifted tile or a small failed KERDI section can be cut out, re-flashed, and re-tiled with the correct banding, which costs far less than a full reinstall. Larger areas where the membrane has de-bonded usually need replacement of the full run.
A targeted tile or membrane repair is typically a 1 – 2 day job; a full kitchen remodel with new Schluter underlayment and tile typically runs several weeks, and we give you a realistic timeline in writing before we start. If your project includes cabinetry or counters from KraftMaid, Cambria, or Silestone, expect the schedule to be coordinated around those lead times.
We order genuine Schluter components through authorized suppliers, matched to your specific membrane, profile, or DITRA-HEAT part number, so the replacement fits the system you already have. We don’t generate a part number from memory – we confirm it against the product label and measurements before ordering.
Groundwork Construction Co. of Los Angeles is an independent service provider and is not affiliated with Schluter. We install and repair Schluter systems as one trade in a full-scope kitchen remodel, backed by our 730-Day Done Right Promise, upfront pricing, and no-hassle 0% financing for 18 months. Every technician is background-checked and arrives in uniform, with up to 12 years of experience on the tools.
Ready for a straight answer on your Schluter kitchen? Call (888) 427-1733 to schedule your free estimate – and if you’re planning a full remodel, ask about the $1,000 off on projects over $10,000. A live person answers any hour of the day.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.