Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Sterling Kitchen Remodeling: The Los Angeles Owner’s Guide
We install and repair Sterling-compatible kitchen remodeling components across Los Angeles, and most cabinet, countertop, and door-part jobs land between $16,520 and $53,100 for a full kitchen scope. Smaller fixes, like a single cabinet box, drawer glide, or door hinge replacement, usually run far less. Same-day availability depends on the part, so call (888) 427-1733 and we’ll tell you honestly what’s in reach for your kitchen.
Owners rarely notice a Sterling part failing until something stops working. A drawer that won’t close all the way. A cabinet door that hangs crooked after years of clean operation. A soft-close hinge that slams. A countertop seam that darkens at the edge. In Los Angeles kitchens, where heat and dry air work on wood and adhesive year-round, these failures show up faster than most homeowners expect. The part itself is usually simple. Matching it to your exact Sterling model is where the job gets interesting.
Key Takeaways
- Sterling cabinet and door parts are matched by series, not by looks alone.
- Full Sterling-compatible kitchen scopes in Los Angeles run $16,520 – $53,100 installed.
- We don’t carry parts on a truck. We source them by model and install them correctly.
- Cabinet hardware and door swaps are homeowner-safe; gas, electrical, and structural work are not.
- Every install is covered by our 730-Day Done Right Promise.
Which Sterling Models This Applies To
Sterling has produced kitchen cabinetry, doors, and related components across several product lines over the years, and the parts aren’t always interchangeable between them. A drawer glide that fits a Sterling frameless cabinet will not fit a framed box from an earlier series. The hinge pattern changes, the bore spacing changes, and the door thickness changes. If you order by photo or by memory, you’ll end up with the wrong part more often than not.
The reliable way to identify your part is to look for the model label inside the cabinet box, usually on the inside of the door or on the back panel, and to measure the existing part before you replace it. For hinges, that means the cup diameter and the overlay. For drawer glides, that means the length, the mounting pattern, and whether it’s side-mount or under-mount. For doors, that means the width, height, thickness, and hinge bore position.
On OEM versus aftermarket: Sterling-branded replacement parts are the safest match when the cabinet is under ten years old and the series is still supported. Aftermarket equivalents from brands like Blum, Grass, or Hettich will often fit Sterling boxes and can outperform the original hardware, but only if the mounting pattern lines up. We confirm fit before we install, not after. We’re an independent service provider and are not affiliated with Sterling, so we source parts by measurement and model spec, not by brand assumption.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Sterling Kitchen Remodeling Is Failing
Most Los Angeles homeowners call us after one of these five things happens. Each points to a different underlying part, and each is fixable.
- Drawers that stick or won’t close flush. Usually a worn glide or a sagging slide rail. In older Sterling boxes, the screws backing out of the rail is the first sign the glide is failing.
- Cabinet doors that hang crooked or rub the frame. A tired hinge or stripped hinge screw plate. Left alone, the door eventually pulls the screw out of the box and the fix gets bigger.
- Soft-close doors that slam. The damper inside the hinge has failed. This is common in kitchens that get daily use and see summer interior temps above 85°F.
- Countertop seams that darken or lift at the edge. Adhesive breakdown at the seam, often accelerated by heat from a dishwasher or oven nearby. Wood cabinets move, and the seam shows it.
- Cabinet finish lifting or bubbling near the sink or range. Moisture or heat intrusion under the finish. In Los Angeles, it’s usually steam from a dishwasher vent or a kettle sitting too close.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what Sterling-compatible kitchen work runs in Los Angeles, installed. These are real ranges, not teaser prices.
| Scope | Installed Range (Los Angeles) |
|---|---|
| Full kitchen remodel | $16,520 – $53,100 |
| Small kitchen remodel | $10,620 – $23,600 |
| Cabinet installation | $4,720 – $15,340 |
| Countertop installation | $2,360 – $7,670 |
| Backsplash installation | $945 – $2,950 |
| Kitchen island installation | $3,540 – $11,800 |
What drives the range: cabinet size and box count, whether the layout changes, countertop material (Cambria and Silestone priced higher than stock quartz), and whether electrical or plumbing has to move. Parts and labor are broken out in writing. No-hassle upfront pricing means the number you see is the number you pay, and every install carries our 730-Day Done Right Promise. We’re proud to offer 0% financing for 18 months and $1,000 off projects over $10,000.
DIY or Call Us?
Some Sterling work is genuinely homeowner-safe. Replacing a single cabinet knob or pull, swapping a door if the hinge bore already matches, or tightening a loose drawer glide with the right screws is fine for a careful owner with basic tools.
What goes wrong: matching the wrong part and forcing it. A hinge cup that’s 2mm off will crack the door. A drawer glide that’s the wrong length will misalign the drawer face and pull the box out of square. Countertop and backsplash work involves cut stone, adhesive, and sometimes gas or electrical connections nearby, and that’s where we draw the line. If your work touches a gas line, a 240V range circuit, or structural cabinet anchoring, stop and call a trained professional. Not because it’s hard to explain, but because the failure mode is expensive or dangerous. Call (888) 427-1733 and we’ll give you a straight answer on whether your job is a one-hour fix or a full scope.
FAQs
Most Sterling soft-close hinges last 8 to 12 years in daily-use kitchens, and drawer glides last 10 to 15 years before the slide rail wears. In Los Angeles, dry air and summer interior heat can shorten that by a year or two, especially near a range or dishwasher vent. Call (888) 427-1733 for a replacement quote.
Sometimes. A tired hinge can often be adjusted or retightened, and a stuck glide can sometimes be cleaned and re-seated. But once the damper is gone or the screw plate is stripped, replacement is the honest answer. We’ll tell you which one your part needs before you spend a dollar.
A single hinge or glide swap is usually under an hour. A full cabinet door set or drawer bank is typically a half-day. A countertop or backsplash replacement is a scheduled project, not a same-day visit. Call us with your model and scope and we’ll give you a realistic timeline.
We match by model label and physical measurement, not by photo. For older series where the Sterling part is discontinued, we identify a spec-matched aftermarket equivalent and confirm fit before install. Call (888) 427-1733 with your model number and we’ll confirm availability. We also service KraftMaid, Cambria, and Silestone kitchens when your scope crosses brands.
Call (888) 427-1733 for a free estimate on your Sterling kitchen work. A live person answers 24/7, our technicians are background-checked and arrive in uniform, and your project is backed by our 730-Day Done Right Promise. From foundation to finish line, we handle it.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.