Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Bathroom Remodeling: The Los Angeles Owner’s Guide
Tamko bathroom remodeling in Los Angeles typically runs $10,620 to $33,040 installed, with most single-bathroom projects landing in the middle of that band once tile, waterproofing and fixtures are folded in. Tamko is a roofing and waterproofing manufacturer, not a bathroom fixture brand, so when we talk about “Tamko bathroom work” in Los Angeles we mean the moisture-protection layer of a remodel: underlayment, waterproofing membrane, and the roof-to-wall flashing where bathrooms sit against attic or exterior walls. Most owners here don’t discover a problem with that layer until a ceiling stain shows up below a second-floor bath, grout starts cracking at the shower curb, or a contractor pulls old tile and finds soft, dark sheathing behind it.
Which Tamko Models This Applies To
Tamko’s bathroom-relevant products fall into a few families, and matching the right one matters more than the label on the box. Their waterproofing membranes and underlayments are sold under product lines that pair to specific tile assemblies and substrates; their roofing and flashing lines (the ones that fail where a bathroom addition meets the main roof) are a separate family entirely. A homeowner can usually identify what’s installed by pulling a scrap from the demo pile and reading the printed roll edge or the stamped backer, or by checking the permit drawings if the previous bath was permitted. Measurements then confirm it: membrane rolls have fixed widths and thickness specs that differ across product lines, so a 3-inch over-cut one way or the other tells you which family you’re holding.
The OEM-versus-aftermarket call for Tamko comes down to where the part sits. Waterproofing and flashing are assembly-dependent: the membrane, the primer, the corner pieces and the drain flange are designed to work as a system, and mixing brands inside one shower pan is where slow leaks begin. For loose, non-structural pieces, a quality aftermarket equivalent is fine. For anything forming the waterproof envelope, we source to the manufacturer’s spec. That’s the difference between a bathroom that lasts and one that’s back open in four years.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Bathroom Remodeling Is Failing
Waterproofing problems don’t announce themselves. They surface slowly, and by the time a Los Angeles owner sees one, the damage has usually been running for months. These are the symptoms we find most often:
- Cracked or hollow grout lines at the shower floor and curb. The membrane underneath has lost its bond or shifted, so the tile moves independently of the substrate and the grout telegraphs the failure.
- A ceiling stain directly below a second-floor bathroom. Water has worked past the pan or the wall membrane and is traveling along the framing before it drips. This one is the warning shot.
- Soft or dark sheathing found during a gut. The underlayment absorbed moisture it was never meant to hold, and the wood behind it is breaking down. You only see this once the tile’s off, which is exactly why we slow down at demo.
- Musty smell that returns after cleaning. Moisture is trapped in a wall cavity or under the floor, and no amount of bathroom cleaner will reach it. The smell is a symptom, not the problem.
- Flashing gaps where the bathroom addition meets the roof. In Los Angeles, summer heat cycling opens these seams, and the first fall rain finds them. This is the Tamko roofing-side failure most often mistaken for a plumbing leak.
Replacement Cost & What’s Included
Installed pricing for the waterproofing and flashing layer inside a full Los Angeles bathroom remodel runs $10,620 to $33,040 as part of the project; a small bathroom remodel sits at $5,900 to $14,160. What drives the range is how much of the bath is being opened: a membrane-and-flashing repair inside an existing layout sits at the low end, while a full gut that replaces the envelope, substrate and finish tile lands high.
We quote line items, not a lump. You’ll see membrane, primer, corner pieces, drain flange, substrate, tile and labor written separately, with the materials spec’d to the manufacturer. The number you see is the number you pay. Every bathroom we finish carries the 730-Day Done Right Promise: if it’s not done right, we make it right. That’s the guarantee sitting behind the waterproofing layer nobody sees.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
An owner can safely check the obvious: look for a stamped roll edge on any exposed membrane, pull the access panel on the shower valve to check for active drips, and get on a ladder to eyeball the flashing where the bathroom wall meets the roof. That’s inspection, and it’s useful.
What we don’t recommend is resealing a shower pan or re-flashing a roof-to-wall joint yourself. The membrane in a shower is a bonded, integrated envelope; a homeowner patch over a failing pan tends to trap water against the substrate instead of stopping it, and the leak surfaces somewhere worse six months later. Roof flashing at height on a Los Angeles slope is a fall risk, plain and simple. When the envelope is the question, call a professional. Reach us at (888) 427-1733 and we’ll tell you honestly whether it’s a patch or a rebuild.
FAQs
Properly installed and ventilated, a bonded membrane and flashing assembly should hold 20 to 30 years. Los Angeles is hard on it differently than a wet-climate city: our dry summers and UV load break down surface sealants faster, while an occasional winter storm finds every seam. Call (888) 427-1733 for an exact quote; estimates are free.
Sometimes, yes: a single failed flashing seam on a bathroom addition roof can often be re-flashed without touching the interior. A failed shower pan almost never repairs cleanly, because the leak has already wet the substrate. We inspect before we quote, so you know which one you’re facing.
A flashing repair is typically a day. A shower membrane replacement with new tile runs several days once the pan is opened and the substrate dried to spec. Most jobs stay in a single continuous visit. Call (888) 427-1733 for a real timeline on your Los Angeles bathroom.
We read the existing roll edge or stamped backer, confirm the assembly, and source to the manufacturer’s current spec for that product family. If the original line is discontinued, we match the assembly-compatible replacement rather than forcing a generic. Call (888) 427-1733 to start your free estimate and design consult.
Ready for a straight answer on your Los Angeles bathroom?
Groundwork Construction Co. of Los Angeles is an independent service provider and is not affiliated with Tamko; we install and service to manufacturer spec, and we partner on KraftMaid, Cambria and Silestone for the fixture and finish side of the job. Our technicians bring up to 12 years of experience, background-checked and in uniform, and the phone is answered by a live person 24/7. Call (888) 427-1733 for your free estimate and design consult; we also offer $1,000 off projects over $10,000 and 0% financing for 18 months.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.