Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Kitchen Remodeling: The Los Angeles Owner’s Guide
We handle Tamko-compatible kitchen remodeling across Los Angeles, and a full kitchen remodel here typically runs $16,520 – $53,100 installed. Most of the calls we get aren’t about a single broken part at all: owners discover the problem months after the fact, when the material in a Tamko-spec kitchen starts letting go along a seam, a flashing edge, or a low-slope ceiling below an upper floor. You notice a ripple in the surface, a soft spot near the sink, or a stain on the ceiling under the bathroom above, and only then do you start tracing it back to what was actually installed.
We’re an independent service provider. We install Tamko-compatible materials and systems, but we’re not affiliated with Tamko. That distinction matters on a parts-driven job, because our loyalty is to getting the right material matched to your build, not to moving whatever a distributor has on hand.
Which Tamko Models This Applies To
Tamko’s residential line spans several product families, and the one people most often bring us in Los Angeles is its roofing and weather-barrier material, which shows up above kitchen bump-outs, additions, and flat or low-slope sections over a remodeled kitchen. When a kitchen gets extended or an existing covered patio is folded into the footprint, that transition detail is where Tamko material usually gets specified. If your project includes a Tamko underlayment or membrane, the identifying label is normally on the roll end or inside the bundle wrap, and it will carry a product name plus a spec code. Take a photo of that label before anything gets cut. The compatibility gotcha we run into: Tamko’s self-adhered and nail-applied lines have different substrate requirements and different minimum-slope tolerances, so a membrane that’s right for a 4:12 roof can be wrong for the nearly flat section over a kitchen addition. Match the product code, not the color.
On the OEM-versus-aftermarket question, Tamko-branded accessories (their flashing tapes, primers, and edge metal) are worth matching to the membrane because the manufacturer’s system is tested together. Aftermarket equivalents can be fine, but only when the spec sheet lines up on thickness, adhesive type, and temperature rating. A distributor’s “equivalent” that’s a few mils thinner is not equivalent. We verify before we order, and we put what we specified in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Kitchen Remodeling Is Failing
In Los Angeles, most of these failures trace to sun exposure and the dry-then-wet swing of our rain season, not to cold. Here’s what we actually see:
- Seam separation on the membrane or flashing: the adhesive or sealant has released along a lap, usually where a remodeled kitchen roof meets an existing wall. UV baking over several summers accelerates it, and the first real storm finds the gap.
- Soft or spongy decking under a low-slope kitchen roof: water has been getting in slowly and the substrate is holding moisture. By the time it feels soft underfoot, the decking is already compromised.
- Staining or bubbling on the kitchen ceiling after rain: the classic sign that water is tracking along a detail above and finding a low point well away from the actual leak. The stain is rarely directly beneath the failure.
- Granule loss or surface checking on Tamko shingle sections: normal aging, but in Los Angeles the pace depends heavily on whether the section faces full afternoon sun. Checking that shows up on a 15-year-old field is expected; the same checking at year five is not.
- Lifted or curled edges at the perimeter and penetrations: wind and thermal movement work the edges first, especially around vents and where a kitchen addition ties into the original roofline. A curled edge is an open door for water.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For the kitchen remodeling work this connects to in Los Angeles, here’s how upfront pricing breaks down. The number you see is the number you pay, and we put the line items in a written quote before anyone touches the house.
| Work | Installed Range |
|---|---|
| Full kitchen remodel (incl. Tamko-compatible roofing/weather barrier where applicable) | $16,520 – $53,100 |
| Small kitchen remodel | $10,620 – $23,600 |
| Cabinet installation | $4,720 – $15,340 |
| Countertop installation | $2,360 – $7,670 |
| Backsplash installation | $945 – $2,950 |
| Kitchen island installation | $3,540 – $11,800 |
What drives the range: the size and slope of the roof or membrane section, whether decking needs replacement, access, and how much of the kitchen gets touched. Labor and material are both itemized. Every project is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. We also carry $1,000 off projects over $10,000 and 0% financing for 18 months, and the first estimate and design consult are free.
DIY or Call Us?
There’s a real safety line here. Roof and membrane work over a kitchen addition means climbing and working at height, and a self-adhered membrane has to go down on a properly cleaned, primed, dry substrate at the right temperature or it will simply not bond. That’s not a scare tactic; it’s why so many weekend membrane jobs leak at the first rain. We recommend a trained professional for anything above ground level or involving a roof-to-wall detail.
What you can safely do: check your paperwork for the Tamko product code, photograph any remaining label, look for stains on the kitchen ceiling after a storm, and note where water shows up versus where the roof detail is. Those notes are exactly what we need. Our technicians have up to 12 years of experience, and every one is background-checked and arrives in uniform. Call (888) 427-1733 and a live person answers, 24/7.
FAQs
Expect roughly 15 to 25 years for shingle sections and longer for quality membrane on a properly prepared substrate, but Los Angeles sun is the variable: a section taking full afternoon exposure ages faster than one under shade, and our dry summers followed by winter rain stress seams more than a steady climate would. Call (888) 427-1733 for an exact read on your roof or membrane, and the estimate is free.
Often yes. Isolated seam separation or a single failed flashing detail can usually be repaired rather than replaced, as long as the decking underneath is still sound and the rest of the field has life left. We tell you honestly which one you’re dealing with. Call (888) 427-1733 to schedule your free estimate.
A targeted repair over a kitchen section is usually a short job, while a full membrane or roof section plus the kitchen work around it takes longer and depends on access and decking condition; we give you the timeline in the written quote. Call (888) 427-1733 to schedule your free estimate.
We start from the product code on your label or paperwork and match it on product family, thickness, adhesive type, and slope tolerance, then confirm what we specified in writing before ordering. When your kitchen also involves cabinets or counters, we work with KraftMaid, Cambria, and Silestone on the same job. Call (888) 427-1733 to schedule your free estimate.
If you’re planning a Tamko-compatible kitchen remodel in Los Angeles, or you’ve spotted the early signs of a failing section over your kitchen, don’t wait for the ceiling stain. Our team brings upfront pricing with no surprises, background-checked uniformed technicians, and the 730-Day Done Right Promise on every project. Call (888) 427-1733 today to schedule your free estimate and design consult. A live person answers around the clock.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.