Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Windows & Doors: The Los Angeles Owner’s Guide
We install and repair Tamko-compatible windows and doors across Los Angeles, and full window replacement here typically runs $5,310 – $17,700, while impact-rated units run $9,440 – $29,500. The part itself is rarely the expensive piece; the labor, flashing, and finish work around it are. Most owners discover a failure the same way: a window that sticks in August, a door that whistles at the edges in winter, or fog trapped between the panes. Groundwork Construction Co. of Los Angeles is an independent service provider and is not affiliated with Tamko.
Tamko makes a strong line, but Los Angeles weather stresses it in predictable ways. Our technicians have up to 12 years of experience. Every job we do is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right.
Which Tamko Models This Applies To
Tamko window frames and patio doors live across several product lines, and picking the wrong replacement part is the most common mistake we see. Before we quote anything, we read three things off the unit: the manufacturer label in the top or side jamb channel of a vinyl window, the frame dimensions (measure the rough opening, not the glass), and the series code stamped on the sash or spacer bar. If the label has worn off, we measure the rough opening, glass thickness, and hinge or roller locations ourselves.
Tamko’s vinyl window line is a good example of a compatibility gotcha: newer production uses a narrower perimeter channel than earlier frames, so a replacement sash, balance, or weatherstrip sold for the older profile fits loose or not at all. That’s a measurement problem, not a brand problem.
On the OEM-versus-aftermarket call, it depends on the part. For a window balance or door sweep, a quality aftermarket equivalent with the correct width and length meets the job fine. For a lock, multi-point hardware, or glazing-bead component, we match the Tamko part whenever it’s still available. We claim no stock of parts and carry nothing on a truck – we identify your part, then supply it. In Los Angeles, a coastal salt-air exposure near Santa Monica and a hot Valley sun in the San Fernando Valley attack the same frame in different ways, and the part spec should reflect that.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Windows & Doors Is Failing
- The window sticks or won’t slide. The balance spring has weakened or the sash has warped from sun and heat, so it drags in its track instead of gliding.
- Fog or condensation between the panes. The factory seal on the insulated glass unit has failed, letting moisture migrate into the sealed cavity.
- A door whistles or leaks air at the edges. The weatherstrip, sweep, or sill is worn or misaligned, breaking the seal that keeps outside air out.
- The lock or multi-point hardware binds. The strike plates have shifted with the house settling, or the cam and keeper have worn, so the door no longer seals shut cleanly.
- Water staining or soft spots at the sill. Failed flashing or a worn sill has let moisture in, and the wood or frame beneath is absorbing it.
Any one of these is a sign worth a look. Two or three together usually means the whole unit, not just the part, needs attention.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for Los Angeles depends mainly on unit count, glass spec, and whether we’re swapping a part or a full unit. These are real numbers that include materials, labor, and cleanup.
| Service | Typical Installed Range |
|---|---|
| Window replacement (full unit) | $5,310 – $17,700 |
| Impact window installation | $9,440 – $29,500 |
| Door hardware / weatherstrip / balance repair | Quoted at the visit, line-item |
What pushes a job toward the top of the range: impact glass, larger openings, upper-floor access, and older frames that need reframing. We quote parts and labor as a written line-item list, so you see exactly what a balance costs versus the glass versus the install. No-hassle upfront pricing – the number you see is the number you pay. The work is backed by our 730-Day Done Right Promise.
DIY or Call Us?
There’s a safe line here, and it’s worth knowing where it sits. You can check a window by looking for a label, measuring the rough opening, and testing whether the sash is warped or just dirty. You can inspect a door seal by holding a piece of paper in the gap and sliding it shut – if it pulls out with no resistance, the weatherstrip is gone. Those checks cost nothing and tell you a lot.
Where DIY goes wrong is the sealed glass unit and the multi-point lock hardware. Replacing an insulated glass unit yourself means breaking a factory seal and re-glazing correctly, and a bad seal fails again in one Los Angeles summer. Tamko locks and rollers also need the right part, not a universal one from a shelf.
If you’ve found the problem and want it fixed right, call (888) 427-1733. A live person answers, 24/7, and estimates are free.
FAQs
The frame usually holds 20 to 30 years, but the seal on the glass unit and the weatherstrip wear out far sooner – often 10 to 15 years in sun-exposed spots like the San Fernando Valley. UV and heat are the main killers, so a Valley-facing unit ages faster than one in shade. Call (888) 427-1733 for an exact quote – estimates are free.
Usually yes. A failed balance, a worn sweep, or a binding lock is a part swap, not a new unit. Full replacement only makes sense when the glass seal is gone or the frame is warped or water-damaged. We tell you which it is after we look.
A single part repair is often done in one visit, usually under two hours. A full window or door unit install takes most of a day per opening, sometimes two with reframing. Most jobs we do are completed in a single visit.
We identify your exact series and model from the label or measurements, then supply the matching part – OEM when it’s still available, a quality equivalent when it isn’t. We don’t claim to stock parts and don’t keep them on a truck; we source yours to spec.
If you’ve got a Tamko window or door that’s failing, call (888) 427-1733 for a free estimate. We also handle KraftMaid, Cambria, and Silestone on other projects – and we back the work with our 730-Day Done Right Promise and 0% financing for 18 months. Call (888) 427-1733 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of Los Angeles, serving Los Angeles and nearby areas.