Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Stevenson Ranch: What It Costs and How Long It Takes
A wrought iron fence in Stevenson Ranch typically runs $3,500 to $9,000, with most hillside-lot front yards landing in the $4,800 to $7,200 range once gates, sloped-set posts, and an ARB-compliant finish are included. A standard run of 100 to 150 linear feet takes two to four working days on site, but the architectural-review approval that usually comes first can add two to four weeks to the calendar. Call (888) 427-1733 and we’ll walk through your lot, your HOA’s standards, and a written line-item number before anything gets ordered.
How a Groundwork Iron Fence Goes In, Stage by Stage
Iron fence work in Stevenson Ranch runs on a fixed sequence, and the homeowner’s decisions cluster at the front and the back of it. Here’s what actually happens.
Stage 1: Site walk and setback check (day 1, about an hour)
We measure the run, mark post locations, and check the property line against your plat. On graded and hillside lots off Sagecrest or Southern Oaks Drive, we’re also checking where the slope turns and how much grade each panel has to absorb, because that single decision pushes post spacing from a standard 8 feet down to 6 feet. You decide the fence height and the panel style now, before any order is placed.
Stage 2: HOA and architectural submittal (1 to 4 weeks)
Stevenson Ranch has multiple HOAs, and most require architectural-review-board approval before iron goes up. We prepare the submittal drawings, color chips, and post-cap specs your board asks for, and we match whatever the community standard already dictates. This is the step that catches homeowners who buy first and submit second. You decide the finish color here, and it has to be a color the board approves.
Stage 3: Layout, demo of the old fence, and post setting (days 1 and 2 on site)
We pull the old fence and set posts in concrete, plumb and true to grade. On post-tension slabs and raised foundations common in this housing stock, we don’t core into structural concrete without knowing what’s underneath, so post placement follows the slab edge rather than crossing it. You decide nothing here; this is our stage to get right.
Stage 4: Panel hang, gate fit, and hardware (day 3)
Panels go up, gates get hung and adjusted, and self-closing hardware is set so the gate latches cleanly every time. If the fence pairs with a driveway entry, this is when the gate swing and clearance get finalized.
Stage 5: Touch-up and walkthrough (day 4)
We touch up welds and scratches, check every post for plumb, and walk the run with you. Any punch item gets written down and closed out before we leave. The work is covered by our 730-Day Done Right Promise, so a gate that sags in month eight gets fixed, not argued about.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options Stevenson Ranch Homeowners Pick Between
Not all “wrought iron” is the same product, and the spec choices below are where the honest trade-offs live.
- Mild steel with a powder-coat finish – the most common pick here. Runs $45 to $75 per linear foot installed. Holds color well against dry summers, and the powder coat is what keeps rust at bay. Suits most Mediterranean and Spanish-style homes.
- Galvanized steel, hot-dip – $60 to $95 per linear foot. Heavier, more rust-resistant at welds and cut ends, and the better call on lots backing onto the open hillside where wind-driven dust abrades finish.
- Cast aluminum – $55 to $90 per linear foot. Lighter, rust-proof, and a strong fit for HOAs that want an iron look without the weight. Won’t take the same impact as steel.
- Panel vs. custom fabrication – stock panels are cheaper and faster; custom runs let us follow a curved or stepping grade without visible gaps at the bottom rail. On hillside lots, custom usually wins.
- Finish color – satin black is the community standard in nearly every Stevenson Ranch HOA. Bronze and dark green occasionally clear review; bright colors don’t.
- Gate hardware – self-closing hinges and a child-safe latch add $150 to $400 per gate and are often required by the board.
What an Iron Fence Costs in Stevenson Ranch, CA
The range is $3,500 to $9,000 for a residential iron fence here. Below is how a written estimate breaks down.
| Line item | Typical range |
|---|---|
| Iron fence, 100-150 linear ft, installed | $3,500 – $7,500 |
| Driveway or pedestrian gate | $400 – $1,200 each |
| Custom fabrication for grade changes | $300 – $900 |
| Demo and haul-away of old fence | $250 – $700 |
| HOA architectural submittal support | Included |
What pushes a job to the low end: a flat, short run, stock panels, satin black powder coat, and no gate. What pushes it to the high end: a steep slope that forces shorter post spacing, a long run past 150 feet, custom fabrication, two gates with self-closing hardware, and a heavier galvanized or cast aluminum spec. A hillside footing that has to be pinned into a retaining wall adds cost too. What’s included: material, labor, concrete for post setting, submittal drawings, and cleanup. What usually isn’t: retaining wall work, and any gate automation. Estimates are free and line-itemed, so you see the number before you commit.
See the difference
Before
After
Before
After
Before
AfterWhat Stevenson Ranch Homes Specifically Do to This Job
Stevenson Ranch is an unincorporated, master-planned community in ZIP 91381, and the terrain and codes here change iron fence work in ways they don’t in neighboring Santa Clarita or Valencia. Nearly every lot sits on a graded slope in a high-fire-severity zone, so Chapter 7A fire-hardening and hillside standards drive a lot of what gets built, and those same hillside conditions are why fence posts here step down a slope rather than follow one flat line. The housing stock is mostly 1980s to 2000s Mediterranean and Spanish-style tract homes plus hillside custom builds with stucco exteriors, tile roofs, and post-tension slab or raised foundations. Permitting often runs through LA County rather than the City of Santa Clarita, and HOA design review is a second approval layer on top of that. On homes backing onto the greenbelt slopes, the wind exposure on the Santa Ana side is a real factor: ember intrusion and blistered finishes show up first on fence sections left unscreened. We see the same failure pattern again and again – posts that weren’t set deep enough on a graded lot lean after a winter rain season. We set them to the slope, not to a standard flat-lot depth.
Serving Stevenson Ranch, CA – Our Local Coverage Area
We serve Stevenson Ranch and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Stevenson Ranch
Two to four working days on site for a typical residential run of 100 to 150 feet. The HOA architectural review that usually precedes the work is what stretches the calendar to two to four weeks total, so plan around the review, not the install.
Often yes, and it depends on height and location. Fences below the county threshold usually don’t require a building permit, but anything taller, or any fence on a slope or retaining structure, typically does. We confirm the requirement for your specific lot before we order material – call (888) 427-1733 and we’ll check it with you.
Yes, and that’s the part we handle first. We pull the community’s approved style, height, and finish, and prepare the submittal drawings so the fence goes in without a violation notice afterward. Satin black powder coat clears nearly every board here.
Most jobs land between $3,500 and $9,000. The variables that move that number are run length, grade changes, gate count, and material grade. Call (888) 427-1733 for an exact written quote – estimates are free.
Every iron fence install is backed by our 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship, not damage from vehicles or extreme weather, and it’s in writing.
No. Your written estimate is a fixed price, with no change orders unless you request a scope change. That’s upfront pricing, no surprises. Call (888) 427-1733 to lock in a number.
Get a Free Iron Fence Estimate in Stevenson Ranch
If you’re ready to price an iron fence in Stevenson Ranch, call (888) 427-1733. A live person answers around the clock, and we’ll schedule a free on-site estimate. On that visit we measure the run, check grade and setbacks, and review your HOA’s standards with you. You’ll leave with a written, line-itemed number and a clear read on timing. If the fence is part of a larger project, it can be scoped into a full Fence Installation in Stevenson Ranch, and homeowners often pair this with Patios, Walkways & Pool Decks in Stevenson Ranch to finish the yard in one pass. Our Fence Installation team covers the broader work, we serve all of Stevenson Ranch, and an ADU Design & Permitting in Stevenson Ranch project is another common add-on. Call today to start.
Written by the team at Groundwork Construction Co.