Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Santa Clarita, CA: What It Costs and How It’s Done
Metal roofing in Santa Clarita runs $15,000 – $40,000 installed for most homes here, depending on roof size, panel type and how much fire-rated detailing your Very High Fire Hazard Severity Zone address requires. A typical re-roof takes 3 – 6 working days once the material is on site. Call (888) 427-1733 and we’ll price your roof against the actual ARB and City of Santa Clarita requirements for your tract, not a ballpark over the phone.
How a Metal Roof Goes On: The Stage-by-Stage Sequence
Metal is a different animal from tile or shingle, and the order of operations matters. Here’s what actually happens from the day we start to the day you pass final inspection.
Stage 1: HOA paperwork and permit submittal (1 – 3 weeks before any work)
This is where most Santa Clarita metal jobs live or die, so we start here. We pull your community’s architectural guidelines, confirm the approved panel profile and color for your subdivision, and put together the ARB submittal package for you. In parallel, we submit the re-roof permit to the City of Santa Clarita. You’ll need to decide the panel profile and color now, because the ARB package locks them in.
Stage 2: Tear-off and deck inspection (1 – 2 days)
We strip the old roofing down to the sheathing and walk the deck with you or send photos. Soft or delaminated panels get replaced, and this is the point where a hidden fascia or flashing repair turns up. You approve any deck remediation in writing before we go further, so the number doesn’t move after the fact.
Stage 3: Underlayment, battens and fire-rated detail (1 – 2 days)
On a Chapter 7A assembly, the underlayment and eave, valley and vent detailing are part of the fire rating, not an optional extra. We install the high-temp underlayment, the battens or purlins for the panel system, and the ember-resistant venting. You decide here whether to upgrade to a fully sealed attic-vent assembly, which many Canyon Country and Saugus homeowners do because of the wind-driven ember exposure.
Stage 4: Panel setting and fastening (2 – 3 days)
This is the visible part. Panels go up, get aligned and fastened to the manufacturer’s wind-uplift spec, and we check every plane before closing out the trim. Santa Ana winds funneling through Soledad Canyon and the Santa Clara River corridor are the reason we spec the fastening pattern we do. It’s not over-building; it’s building for the actual conditions.
Stage 5: Trim, flashing, inspection and final walk (1 day)
Ridge, hip, valley and penetration flashings get finished; we schedule the City inspection; and we do a final walk with you to confirm drainage, clearances and defensible-space lines. The whole sequence is 3 – 6 days of on-site work, but plan for 4 – 8 weeks from first call to final inspection because the ARB and permit clock runs before we touch the roof.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Metal Roofing Options You’ll Choose Between
There’s no single “metal roof.” What you pick drives both the price and how the finished roof reads against your neighbors’ tile. Here’s the honest trade-off on each.
- Standing seam (concealed fasteners): the cleanest look and the best wind performance, with fasteners hidden under the seams. Suits hillside custom homes in Canyon Country. Higher material cost, and the profile is more likely to need ARB approval in a tile-dominant tract.
- Exposed-fastener panels (screw-down): the value option. Cheaper by a meaningful margin and quicker to install, but the fasteners and washers are the long-term wear point and need periodic checking. Fine for outbuildings and some re-roofs; less common as a full house roof where HOA standards are strict.
- Stone-coated steel tile: a steel panel formed and coated to mimic barrel or flat tile. This is the option that most often clears a Santa Clarita ARB because it matches the community’s tile look while delivering metal performance. Sits in the middle of the price range.
- Galvalume vs. painted steel vs. aluminum: Galvalume is the budget workhorse; painted steel gives you a color match to HOA palettes and holds finish better; aluminum costs more but resists corrosion where coastal moisture creeps in. For most Santa Clarita homes, painted steel hits the useful middle.
- Reflective vs. standard finish: a cool-roof reflective finish cuts attic heat load in our hot dry summers, and some utility programs and City green-building provisions reward it. Worth pricing both before you commit.
What Metal Roofing Costs in Santa Clarita, CA
Expect $15,000 – $40,000 for a full metal roof installation in Santa Clarita. The low end is a modest single-story tract home with an exposed-fastener or stone-coated system and a simple roofline; the high end is a larger two-story or hillside home with standing seam, complex hips and valleys, and full Chapter 7A detailing.
Here’s what actually moves the number:
| Cost factor | What it does to the price |
|---|---|
| Roof size and pitch | Larger footprint and steeper pitch both add labor and material; a complex roofline adds cutting and waste. |
| Panel system | Exposed-fastener at the low end, stone-coated steel in the middle, standing seam at the high end. |
| Chapter 7A / WUI requirements | Fire-rated underlayment, ember-resistant venting and detailing add cost – but they’re required in most of the city’s VHFHSZ. |
| Deck condition | Soft sheathing, fascia or flashing repair adds to the job. We price it as a line item, never a surprise. |
| Permit and ARB scope | City permit fees plus any ARB submittal requirements factor in. |
A written estimate from us is line-item: tear-off, deck repair allowance, underlayment, panel system, trim and flashing, permit, and disposal. What it typically doesn’t cover unless we call it out: structural framing changes if the deck reveals a problem, skylight replacement, and gutter replacement – which we price separately. Upfront pricing means the number you see is the number you pay, and any deck finding gets your written approval before we proceed.
See the difference
Before
After
Before
After
Before
AfterWhat Santa Clarita Homes Specifically Do to This Job
Santa Clarita is a master-planned, mostly post-1960s city, and that shapes metal roofing here in ways a contractor from the San Fernando Valley often misses. The housing stock is dominated by tract subdivisions in Newhall, Valencia, Saugus and Canyon Country, plus custom homes on Canyon Country hillsides – and nearly all of it sits under HOA architectural review. That means your metal roof has to pass two gates before it goes on: the community’s architectural review board and the City’s permit and inspection process. Because most of the city falls in Very High Fire Hazard Severity Zones, permitted re-roofs trigger Chapter 7A roofing and venting rules plus defensible-space scrutiny. And the Santa Ana winds that funnel through the Santa Clara River and Soledad Canyon passes regularly damage roofs and hillside structures, which is exactly why the wind-uplift detailing and fire-rated assembly on a metal roof pay off here. Our technicians have up to 12 years of experience building to these standards, and we do the ARB legwork as part of the job.
Serving Santa Clarita, CA – Our Local Coverage Area
We serve Santa Clarita and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Santa Clarita
The on-site work is 3 – 6 working days for most homes, but budget 4 – 8 weeks from first call to final inspection because HOA architectural review and the City permit run before the crew starts. Call (888) 427-1733 to get a realistic timeline for your address.
Yes to both. A re-roof requires a City of Santa Clarita permit, and most HOAs require architectural review board approval of the panel profile and color before work begins. We prepare the ARB submittal and pull the permit for you – call (888) 427-1733 to start.
No, not without your written approval. We give you an upfront, line-item price and hold it; if tear-off reveals soft decking or hidden fascia damage, we show you and get your sign-off before repairing it. Call (888) 427-1733 for an exact quote.
Sometimes, but in most of Santa Clarita we recommend a full tear-off so we can inspect the deck and install the fire-rated underlayment and venting Chapter 7A requires. A direct-to-deck install can work on some homes; we’ll tell you which applies to yours. Call (888) 427-1733 to find out.
You get a manufacturer warranty on the panel system plus our 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction. Call (888) 427-1733 to review the coverage on the specific panel you choose.
Get a Free Metal Roofing Estimate in Santa Clarita
If you’re weighing a metal roof for your Santa Clarita home, start with a free on-site estimate. Call (888) 427-1733, a live person answers 24/7, and we’ll walk your roof, confirm your HOA’s approved profile and color, and give you an upfront line-item price with no surprises. Financing is available at 0% for 18 months, and projects over $10,000 get $1,000 off. If your wider project includes window work, homeowners often pair this with Window Replacement in Santa Clarita, and for wind-rated upgrades we also handle Impact Windows & Doors in Santa Clarita. As part of a full Roofing in Santa Clarita scope or a standalone re-roof, see our Roofing service for the bigger picture. We cover all of Santa Clarita and the surrounding valley.
Written by the team at Groundwork Construction Co. of Los Angeles.