Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Paver Driveways in Marina del Rey: What the Job Actually Involves
Paver driveways in Marina del Rey run $7,000 – $18,000 for most single- and two-car residential drives, with the typical project landing somewhere near $11,000. A standard install takes 3 – 6 working days once permits and materials are set: one day for demolition and haul-off, one to two days for base and compaction, one to two for laying and cutting, and a half-day for polymeric sand, cleanup, and your walkthrough. Call (888) 427-1733 and we’ll give you a written, line-item estimate before any work begins.
What makes this page different from a generic paver pitch is the salt. In Marina del Rey, exterior metal fails fast, and a driveway is a horizontal plane of steel-edged, steel-fastened, salt-blasted hardware sitting 200 feet from open water. We spec the drive around that reality from the first delivery.
How We Install a Paver Driveway: Stage by Stage
Paver work is 70% what happens under the pavers. The surface you see is the last two days of a six-day job. Here’s the sequence we run.
Stage 1 – Layout and demolition (day 1)
We string-line the drive to the exact width and set the slope away from the garage slab. Then the existing surface comes out – concrete, old pavers, asphalt, or the hard-packed DG we find on the marina’s surviving 1950s bungalows. Figure one full day for a standard 400 – 500 sq ft marina drive, with two trucks hauling debris. You decide on the demolition day whether to keep a small section of existing concrete as a base for a walkway, or take it all out.
Stage 2 – Excavation and base prep (day 2 into day 3)
We excavate to a minimum 8 inches for a paver-over-compacted-base build, which is the depth you need for a 4-inch compacted Class II base, bedding sand, and the pavers themselves. Marina soil is sandy and drains well, which is a genuine advantage here, but the marine layer means we cover and re-tarp the base nightly so it doesn’t saturate before paving. Homeowners decide at this stage whether to add a 6-inch flex base for heavier vehicle traffic, and whether to trench for a future EV conduit. Do it now. Trenching under a finished paver drive costs three times as much later.
Stage 3 – Edge restraint and compaction (day 3)
Base compaction is done in 2-inch lifts with a plate compactor, and we test it before setting the edge. Here’s where Marina del Rey changes the spec: we install composite edge restraint with stainless or hot-dipped galvanized spikes rather than plain steel, because the salt-laden air rolling off the water pits standard spikes within a couple of seasons. The edge is what stops the drive from spreading. It’s also the part nobody sees, which is exactly why we’re picky about it.
Stage 4 – Laying and cutting (days 4 – 5)
Bedding sand goes down, screed to grade, and pavers lay in a running bond, herringbone, or basketweave pattern depending on what you chose in the design consult. A typical marina drive runs 400 – 500 sq ft, and a two-person crew sets 200 – 300 sq ft a day. Cuts around the apron, garage sill, and any curb transition are done wet to keep dust down. You’ll want to be around for the last few square feet – this is where the driveway actually starts looking like a driveway.
Stage 5 – Polymeric sand, cleanup, walkthrough (day 6)
We sweep polymeric sand into the joints, activate it with a light water mist, let it set, and do a final pass. Then we walk the project with you, check every edge and transition, and hand over the care sheet. Two weeks after the polymeric sand cures, you’ll want a light re-sweep of any joints that settled, which we can tell you about at handoff. The whole driveway is covered by the 730-Day Done Right Promise – if a paver shifts, an edge lifts, or the sand washes, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Three decisions carry the job: paver material, pattern, and edging. Everything else is detail.
- Concrete pavers (interlocking). The workhorse. $7,000 – $14,000 for a marina drive depending on size and finish. Holds up to salt air well, resists freeze-thaw (not a marina issue) and cycles, and repairs are simple: lift, replace, re-sand. This is what we put on most Admiralty Way and Washington Boulevard-area drives.
- Clay brick pavers. Warmer look, $10,000 – $18,000. Brick absorbs less moisture and the fired surface shrugs off the marine layer. Heavier, slower to lay, and the upfront cost climbs. Worth it if you want the drive to match a 1950s bungalow or a brick-accented exterior.
- Tumbled or antiqued finish. Adds $800 – $1,500 over standard for the same paver. Softened edges hide the small chips that salt fog and wind-driven grit leave behind. Honest trade-off: softened edges also mean slightly looser joints, so polymeric sand quality matters more.
- Permeable pavers. A real option in the marina, where drainage and runoff matter. Adds roughly 15 – 20% to material cost. Suits owners with site-drainage concerns; overkill for a flat drive with a functional slope and a good apron.
- Pattern. Running bond is the cheapest and most forgiving to install. Herringbone costs 5 – 10% more in labor and handles turning wheels better. Basketweave reads more formal. Pick with your house in mind, not a showroom.
- Edge restraint. We use composite with stainless or galvanized spikes as standard in the marina, not plain steel. Ask any contractor what they install. If the answer is “standard steel,” walk.
What Paver Driveways Cost in Marina del Rey, CA
Expect $7,000 – $18,000 for a paver driveway installation in Marina del Rey, with the median job around $11,000. That range isn’t padding – it reflects five real variables that move the number.
- Size. A 300 sq ft single-car apron lands near $7,000. A 600 sq ft double-car drive with a turning pad gets you to $15,000 – $18,000.
- Existing surface and haul-off. Removing 4 inches of old concrete adds $800 – $1,600. Old pavers or plain dirt cuts that in half.
- Base depth and soil. Marina’s sandy soil usually drains well, but we occasionally hit a saturated pocket or a buried utility line that requires extra excavation and re-compaction.
- Paver material. Standard concrete pavers sit at the low end; clay brick and premium tumbled finishes sit at the high end.
- Site access. A tight marina drive on a mid-rise-adjacent residential parcel with no room to stage a delivery truck means smaller loads and more trips – call it $400 – $900.
A written estimate from us breaks out demolition, base, sand, pavers, edge restraint, polymeric sand, and dump fees as separate lines. It does not include landscaping restoration, driveway lighting, or permits if the driveway is part of a larger project. Those are quoted separately so you know exactly what you’re paying for.
Part of a full Driveway & Pavers in Marina del Rey project – apron replacement plus back patio – gets a combined quote. If you’re considering a garage conversion down the line, our Garage Conversion ADU in Marina del Rey scope includes the apron work.
See the difference
Before
After
Before
After
Before
AfterWhat Marina del Rey Homes Specifically Do to a Paver Driveway
Nearly every paver job here is on a property where the coastal environment is the main driver. Salt fog rolls off the water nightly. A handyman replacing a bolt on a 1970s Admiralty Way condo typically finds galvanized steel already rust-stained – that’s the marina reality, and a paver driveway sits right in it. Edge spikes, paver fasteners, and any metal transition to the garage sill corrode years faster than they would in Culver City or El Segundo a few miles inland. That’s why our standard spec here uses composite edge restraint with stainless spikes, not the painted steel edge you’ll see on inland installs.
Housing stock matters too. Marina del Rey is dominated by 1960s – 1980s mid-rise apartment and condo complexes plus contemporary townhome infill, with a light scattering of surviving 1950s – 60s beach-era bungalows. The single-family drives we work on tend to be the bungalows and the newer townhome infill – small footprints, tight access, sometimes a shared driveway approach. That mix shapes the job: narrower drives, more careful staging, and more frequent coordination with HOA rules on paver color and driveway width. We handle HOA submissions as part of the estimate so you’re not chasing signatures alone.
On permits, most paver-over-existing-surface or paver-over-base installs on a residential drive don’t need a city permit in the marina’s jurisdiction. Full reconstruction that changes curb cuts or affects drainage may. We pull what’s needed and pass inspection before close-out. For the broader picture of what we do in Marina del Rey and how it fits with the rest of our Driveway & Pavers work, those pages drill down.
Serving Marina del Rey, CA – Our Local Coverage Area
We serve Marina del Rey and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Paver Driveways in Marina del Rey
Most marina drives take 3 – 6 working days from demolition to handoff, weather permitting. Small aprons under 300 sq ft run closer to 3 days; a 500+ sq ft drive with a turning pad runs 6. The marine layer doesn’t delay installation, but a wet winter storm pushing an atmospheric river through does – we won’t lay pavers on saturated base. Call (888) 427-1733 and we’ll schedule your estimate around your timeline.
Usually not for a paver install over existing base or existing surface, but full reconstruction that changes curb cuts, drainage, or the driveway approach may require one. We confirm the specific requirement for your address during the estimate and pull permits if needed. Call (888) 427-1733 to set up the on-site visit.
Sometimes, yes, if the existing slab is 4 inches or thicker, structurally sound, and hasn’t cracked through settlement. We core-test it during the estimate and give you an honest verdict. If the slab is failing, pavers laid over it fail with it. Call (888) 427-1733 and we’ll tell you which way your drive goes.
Paver driveways in Marina del Rey run $7,000 – $18,000 installed, with the typical job around $11,000. The low end covers a small concrete-paver apron over an existing sound base; the high end covers a 600 sq ft clay brick drive with demolition, fresh base, and premium edge restraint. Call (888) 427-1733 for a written line-item quote – the estimate is free.
Every paver driveway we install is backed by our 730-Day Done Right Promise – two full years of workmanship coverage. If a paver shifts, an edge restraint lifts, or a joint loses polymeric sand, we return and make it right. Manufacturer material warranties pass through to you on top of that. Call (888) 427-1733 to schedule your free estimate.
Get a Free Paver Driveway Estimate in Marina del Rey
Every paver driveway estimate in Marina del Rey starts with a free on-site visit: we measure the drive, check the existing base and slope, talk through paver and pattern options, and hand you a written line-item quote – typically within 48 hours. No pressure to decide on the spot. Upfront pricing, no surprises. The number on the quote is the number you pay. Call (888) 427-1733 to book your estimate today – a live person answers, 24/7.
Written by the team at Groundwork Construction Co.