Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Vanities, Tile & Fixtures in Culver City, CA: What It Costs and How Long It Takes
Vanities, tile and fixtures in Culver City typically runs $9,000 to $28,000 for a full pull-and-replace of the wet wall, floor tile, vanity, and trim package, and most of those jobs finish in 3 to 5 weeks once materials are on site. The wide range comes down to tile selection, whether the vanity moves, and how much of the original 1920s-40s substrate has to be rebuilt. Call (888) 427-1733 for a free on-site estimate with line-item pricing.
How we run a vanity, tile and fixture job from demo to final caulk line
This is the sequence we follow, and it doesn’t change much whether we’re working in a Carlson Park Spanish bungalow or a 1960s rancho off Sepulveda. What changes is how long each stage runs.
Stage 1: Site protection and selective demo (1 – 2 days)
We mask floors and doorways, shut off water at the fixture stops, and pull the vanity, toilet, and existing tile. On Culver City homes of a certain era, this is where we find out what’s underneath. Original mud-set tile beds, drywall that’s gone soft at the tub line, and cast-iron drains with failing joints are common. You decide here whether we stop and re-scope or keep going with the original plan. We don’t proceed past demo without your sign-off.
Stage 2: Substrate and rough-in (2 – 4 days)
New cement board or a bonded waterproof membrane goes down over the floor and walls. If the vanity is moving or the layout is changing, this is when the plumber relocates the supply and drain lines and the electrician drops a new GFCI circuit for outlets and lighting. On the older Culver City stock, this stage often includes sistering a joist or patching a soft spot the old tile was hiding. You’ll want to have your vanity and fixtures on site or confirmed by the end of this stage so the next crew doesn’t sit idle.
Stage 3: Tile layout and setting (4 – 7 days)
We lay out the tile on the floor first, dry, so you can see the cuts before anything gets thinset. Grout lines, pattern direction, and where the cuts land at the doorway and corners all get decided here. Wall tile goes up next, then the floor, then the shower if it’s part of the scope. Setting tile is slow work and drying time is real, so we build in a full cure before grout.
Stage 4: Vanity set, fixtures and trim (2 – 3 days)
The vanity cabinet gets leveled and anchored, the countertop and sink go on, and we set the faucet, shower trim, toilet, and any accessories. Glass, mirrors, and lighting land in this window too. You’ll make your final decisions on towel bars, mirror style, and trim color before this stage starts.
Stage 5: Grout, caulk, punch list and clean (1 – 2 days)
Final grout and a proper silicone job at every wet joint. Then we walk the room with you, mark anything that needs attention, and fix it before we leave. The 730-Day Done Right Promise covers the workmanship on everything we install, so if a tile pops or a caulk joint fails, we come back.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The choices you’ll actually make on this job
Most of the cost swing lives in these decisions. Here’s what we lay out for homeowners, with the honest trade-off on each.
- Vanity type: A freestanding furniture-style vanity in the $800 – $3,000 range installs fastest and suits the Spanish bungalow look. A built-in with a stone top costs more and takes longer to template and set, but it maximizes storage in a small room.
- Tile material: Porcelain is the workhorse, holds up to moisture, and is the most forgiving on price. Ceramic costs less but chips at edges. Natural stone like travertine or marble looks right in a Spanish Colonial Revival home but needs sealing every year or two and stains if you’re not careful with it.
- Tile size and layout: Large-format tile means fewer grout lines and a cleaner look, but it needs a flatter substrate and more waste on cuts. Smaller tile is more forgiving and cheaper to install in a room with out-of-square walls.
- Countertop: Quartz holds up best in a wet room and needs no sealing. Marble looks great and stains. We install Kohler fixtures as a standard option, and a brand-name countertop adds cost but also resale confidence if you’re selling in the next few years.
- Fixtures and finish: Brushed nickel and chrome are the durable picks. Matte black and brass finishes look sharp but show water spots and cost more. This is the one place we tell people not to overthink it: pick a finish you like and put the savings into the tile.
What Vanities, Tile & Fixtures costs in Culver City, CA
For a full vanity, tile and fixture replacement in Culver City, plan on $9,000 to $28,000. That’s the working range for the whole job, not just materials. Here’s what pushes a job toward the low end versus the high end.
| Line item | Typical range |
|---|---|
| Bathroom vanity installation | $800 – $3,000 |
| Tile installation (floor and walls) | $2,500 – $8,000 |
| Fixture set (faucet, shower trim, toilet) | $800 – $3,000 |
| Substrate and waterproofing | $1,200 – $3,500 |
| Plumbing and electrical rough-in (if relocating) | $1,500 – $5,000 |
| Demo and haul-away | $600 – $1,800 |
What moves the number: tile grade and square footage, whether the plumbing or electrical has to move, the condition of the substrate we find under demo, and whether the job requires permits. A vanity swap in a room with sound walls and existing plumbing sits near $9,000. A full gut with relocated drains, new electrical, and natural stone tile gets you to $28,000 or above.
What’s included in our written estimate: labor, demo, haul-away, substrate, waterproofing, setting materials, grout, caulk, and the fixtures you’ve selected. What’s typically not: the tile and vanity itself if you’re buying direct, permit fees, and any structural repair we find after demo opens the wall. We flag that last one in writing before we start, so there are no surprise change orders. Upfront pricing, no surprises is the promise.
See the difference
Before
After
Before
After
Before
AfterWhat Culver City homes specifically do to this job
Culver City isn’t a copy-paste market. The city’s Spanish bungalows in Carlson Park, Sunkist Park, and Culver Crest were built between the 1920s and 1940s, and most still have original wood lath under stucco walls and mud-set tile beds in the bathroom. When we pull an old vanity in one of these homes, we almost always find one of three things: drywall that’s crumbled behind the tile, a drain stub that’s brittle enough to break on touch, or a floor that’s out of level by half an inch or more. None of that is a deal-breaker, but it does move the job into the upper half of the range.
Permitting is the other Culver City-specific factor. If your bathroom is in the Carlson Park Historic District, even minor facade changes go through Cultural Affairs Commission design review, which can add weeks. Interior work usually moves faster, but any plumbing relocation requires a permit and an inspection. We pull the permits and pass the inspection as part of the job, and we tell you upfront what the city’s review timeline looks like for your address.
The climate matters less for indoor tile, but the coastal moisture does affect how we detail. We spec waterproofing behind every wet wall, not just the shower, and we use a proper moisture-tolerant substrate. If your tile work is part of a larger project, the wider scope belongs to our Bathroom Remodeling in Culver City page, and you can also see the full service on our Bathroom Remodeling hub. We cover the surrounding neighborhoods too, and our Culver City service-area page lays out the full footprint, including Marina del Rey and Santa Monica. Homeowners often pair this interior work with Tile Roofing in Culver City when the roof and bath need attention in the same season, and with Specialty Roofing in Culver City for storm-related repair and fire-resistant detailing in the hills.
Serving Culver City, CA – Our Local Coverage Area
We serve Culver City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Vanities, Tile & Fixtures in Culver City
Most vanities, tile and fixtures jobs in Culver City take 3 to 5 weeks from demo to final walkthrough. The biggest variable is material lead time; a stocked porcelain tile and an off-the-shelf vanity can start the same week, while natural stone and special-order vanities often add two to three weeks to the schedule. Call (888) 427-1733 to get a real timeline for your address.
You need a permit only if the plumbing, electrical, or structure changes. A like-for-like vanity and tile swap usually doesn’t require one. Relocating a drain, adding a circuit, or moving a wall does. We pull the permits and pass the inspection on every job that needs it, and we tell you at the estimate stage whether yours will. Call (888) 427-1733 for a straight answer on your specific scope.
Yes, and on a Culver City bungalow that’s usually the smart move. Keeping the plumbing in place cuts the cost and shortens the schedule, and the vanity just needs to fit the existing rough-in. We measure the drain and supply locations during the estimate and source a vanity that lines up with them. Call (888) 427-1733 to schedule a free on-site measure.
Most Culver City jobs run $9,000 to $28,000 for the full package, with a kitchen or bath carryover pushing the total higher in a larger home. A basic vanity swap and floor tile sits near the low end; a full gut with relocated plumbing and stone tile sits near the top. Call (888) 427-1733 for an exact quote on your job – the estimate is free.
Every job we install is backed by our 730-Day Done Right Promise, which is one of the longest workmanship guarantees in the residential construction space. If a tile pops, a caulk joint fails, or a fixture install causes a leak, we come back and make it right within that window. Call (888) 427-1733 to talk through the warranty on your specific job.
Get a free estimate on your Culver City vanity, tile and fixture job
Tell us the bathroom, the rough square footage, and what you’re hoping to change. We’ll come out, measure, and hand you a written line-item estimate with the exact materials and timeline. No pressure, no filler pages. A real person answers the phone 24/7, and estimates are always free. Call (888) 427-1733 to schedule your on-site visit.
Written by the team at Groundwork Construction Co.