Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Backsplash, Tile & Flooring in Culver City: What It Takes and What It Costs
Backsplash, tile & flooring work in Culver City usually runs $14,000 – $45,000 for a full kitchen tile and flooring package, and most projects take two to four weeks from demo to grout. A backsplash alone is a much smaller job at $800 – $2,500. The number moves with square footage, what’s under the old tile, and how fussy the pattern is. Call (888) 427-1733 for a free on-site estimate before you commit to anything.
How We Run a Tile and Flooring Job, Stage by Stage
Tile work lives or dies on prep. Here’s the real sequence, with honest durations, so you know what to expect on day one versus day ten.
Stage 1: Demo and substrate inspection (1 – 2 days)
We pull the old backsplash, countertop tile, and flooring down to the substrate. On Culver City’s older homes this is where surprises surface: rotten drywall behind a backsplash, cracked mortar beds under floor tile, sometimes a layer of vinyl or linoleum glued over the original. You decide then whether to patch or replace the substrate. We don’t move forward on a soft or uneven base, because tile on a bad floor fails within a year.
Stage 2: Layout and dry-fit (half a day)
Before a single tile is set, we lay out the pattern on the floor or wall and walk you through grout line placement, where cuts land, and how the backsplash meets the counter and cabinets. This is your decision point on pattern direction (stacked, offset, herringbone) and where outlets and switches interrupt the field. Getting this right saves a redo later.
Stage 3: Substrate prep and waterproofing (1 day)
We install cement backer board or an uncoupling membrane, tape and mud the seams, and apply waterproofing where it matters, especially behind a backsplash near a sink or range. Floor flatness gets checked with a straightedge; anything out of tolerance gets leveled. This stage is invisible when it’s done and the whole reason a floor lasts.
Stage 4: Tile setting (2 – 4 days)
Floor tile goes down first, then wall and backsplash. Large-format tile takes longer per piece but fewer grout lines. Mosaic and small hex tile take more time to set evenly. We keep consistent spacing and check lippage as we go. You’ll see the pattern take shape here and can flag anything that looks off before grout goes in.
Stage 5: Grout, seal, and final walkthrough (1 – 2 days)
Grout goes in after the thinset cures. We seal where the material calls for it, caulk the movement joints at corners and where tile meets counter, and clean the whole area. The final walkthrough is where you sign off, and where our 730-Day Done Right Promise starts. If a tile pops or a grout line cracks, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
This is where a tile job stops being a commodity and starts being a design decision. Here’s what most Culver City homeowners weigh, with the trade-offs stated plainly.
- Ceramic vs. porcelain floor tile. Ceramic is the budget pick and fine for low-traffic areas, but it chips and stains more easily. Porcelain costs more per square foot but holds up in kitchens and entryways and handles moisture better, which matters in a coastal-adjacent basin.
- Large-format vs. mosaic. Big tiles (12×24 or larger) mean fewer grout lines, easier cleaning, a modern look, and faster install. Mosaics and hex tile give you pattern and character but cost more in labor because every small piece gets set by hand.
- Backsplash material. Subway tile is the workhorse: affordable, classic, hides imperfections. A slab backsplash (quartz or natural stone) is a statement piece and a bigger ticket. Glass and stone mosaics split the difference.
- Grout and sealer grade. Epoxy grout resists staining and doesn’t need sealing; cement grout is cheaper but needs periodic resealing. For a kitchen backsplash near a range, epoxy is worth the upcharge.
- Underlayment system. A cement backer board or uncoupling membrane adds cost upfront but prevents cracked tile over Culver City’s older, often out-of-level subfloors.
What Backsplash, Tile & Flooring Costs in Culver City, CA
Plan on $14,000 – $45,000 for a complete kitchen tile and flooring package, with a backsplash alone running $800 – $2,500 and floor tile priced by the square foot plus labor. Here’s how those ranges break down by line item.
| Scope | Typical Range |
|---|---|
| Backsplash installation | $800 – $2,500 |
| Floor tile (material + labor) | Priced by square foot, bundled into total |
| Full kitchen tile and flooring package | $14,000 – $45,000 |
Four things push a job toward the high end. Square footage is the biggest lever: a galley kitchen and a large open-plan floor aren’t the same job. Existing condition matters just as much; rotten substrate or a failed mortar bed adds demo and rebuild time. Material grade moves the number, since porcelain and slab backsplash cost more than ceramic and subway tile. And pattern complexity is real labor, because herringbone and mosaic take longer to set than a simple stacked layout.
A written estimate from us lists demo, substrate prep, materials, setting, grout, and cleanup line by line. What it doesn’t include: structural repair if we find framing damage, moving plumbing or electrical, and design fees. We flag those before work starts so the number you see is the number you pay. Call (888) 427-1733 for an exact quote; estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat Culver City Homes Specifically Do to This Job
Culver City isn’t a blank-slate market. Much of the housing stock here dates to the 1920s – 40s: Spanish Colonial Revival and Spanish bungalows in Carlson Park, Culver Crest, and Sunkist Park, with a band of 1950s – 60s ranchos and dingbats near Sepulveda and Washington. In those older homes we regularly find original wood lath under the stucco, cracked mortar beds beneath floor tile, and subfloors that have settled unevenly over decades. That means more demo time and more substrate work than a newer build would need. The coastal-adjacent moisture here also drives deterioration in stucco and wood detail, so a backsplash job sometimes uncovers wall repair that wasn’t in the original scope.
The city’s Cultural Affairs Commission design review adds another layer: in the Carlson Park Historic District, even minor facade changes can require approval, and while interior tile work usually isn’t affected, anything that touches the building envelope may need a conversation. Seismic requirements are part of the backdrop too, since the region sits in an active fault zone.
Serving Culver City, CA – Our Local Coverage Area
We serve Culver City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Backsplash, Tile & Flooring in Culver City
A full kitchen tile and flooring package typically takes two to four weeks, and a backsplash alone usually finishes in two to four days. Demo, substrate prep, setting, and grout each have their own cure times, and we don’t rush the cure. Call (888) 427-1733 and we’ll give you a realistic schedule for your specific space.
Most backsplash and floor tile work doesn’t require a permit, but structural changes, plumbing relocation, or electrical work added to the job can trigger one. We’ll tell you upfront whether your project needs a permit and pull it for you if it does. Call (888) 427-1733 to find out where your job lands.
Yes, in most cases. A backsplash swap and new floor tile can be done without touching plumbing or framing, and that keeps cost and timeline down. If we open a wall and find a problem, we stop and talk to you before doing anything else. Call (888) 427-1733 to schedule your free estimate.
A backsplash runs $800 – $2,500, and a full kitchen tile and flooring package runs $14,000 – $45,000 depending on square footage, existing condition, material grade, and pattern complexity. Call (888) 427-1733 for an exact quote; estimates are free and written line by line.
Every tile and flooring project is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space, and it starts at your final walkthrough. Call (888) 427-1733 to schedule your free estimate.
Get a Free Estimate on Backsplash, Tile & Flooring in Culver City
If you’re ready to price a backsplash, tile, or flooring project, call (888) 427-1733. We’ll set up a free on-site estimate, measure your space, talk through materials and pattern options, and hand you a written line-item quote with no surprises. Our technicians are background-checked and arrive in uniform, and a live person answers the phone around the clock. If the tile work is part of a bigger kitchen project, we can fold that into the same conversation.
Written by the team at Groundwork Construction Co.