Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in Culver City, CA: What to Expect
Concrete driveway installation in Culver City runs $4,500 – $12,000 for most residential jobs, and a full pour takes roughly 3 to 7 days from demo to the day you can park on it. The work covers demolition of the old slab, subgrade prep, formwork, reinforcement, the pour itself, finish, and curing. Call (888) 427-1733 and we’ll set a free on-site estimate for your Concrete Driveways & Concrete Work in Culver City.
The coastal wear pattern that opens most Culver City concrete conversations
Before we talk about concrete, look at ten feet away: the hardware on your garage door. Culver City’s position close to the ocean means salt-laden air settles on metal overnight and stays there. Springs, hinges, rollers, tracks, fasteners, and opener chains corrode years faster here than they do five miles inland. We regularly see galvanized hardware pitting before it hits its rated cycle count, and the failure order is predictable: opener chain first, then hinges and rollers, then the torsion springs. That matters because the driveway and the door sit on the same slab, and if the slab is settling or draining toward the door, the moisture accelerates everything above it. When we scope a driveway, we’re also looking at how the pour will drain away from the garage opening, and whether the hardware upgrade is worth pairing in.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
How we actually build a concrete driveway here – stage by stage
Stage 1: Site walk and measurement (about an hour). We measure square footage, check existing slope and drainage, look for utility boxes, gas lines, and irrigation, and photograph the current slab. You decide the finish (broom, exposed aggregate, or stamped) and whether the apron near the street stays or gets replaced.
Stage 2: Demolition and haul-off (1 to 2 days). The old slab is broken out, rebar cut, and debris hauled off. On Culver City lots, this is also where we find what’s under the slab – old tree roots, a defunct drain line, or a utility run that wasn’t in the drawings. You approve any adjustment before we move on.
Stage 3: Subgrade prep and forms (1 to 2 days). We excavate to the right depth, compact the base, set forms to the correct slope (typically 1/8 to 1/4 inch per foot away from the structure), and place vapor barrier and rebar or mesh. This is the stage that determines whether the slab cracks later, so it gets the time.
Stage 4: Pour and finish (1 day). Concrete arrives, gets placed, screeded, and finished to your chosen texture. You confirm control-joint layout before the finish hardens – those joints are what manage cracking, and their placement is a real decision, not a detail.
Stage 5: Cure (5 to 7 days before vehicle traffic). We keep the slab moist or apply a curing compound, remove forms, and clean the site. You get a walkthrough on when to park on it and what to avoid for the first month.
The options you’ll choose between
- Standard broom finish: the most cost-effective and the most slip-resistant in wet conditions. It ages well and hides minor scuffs. Best for daily-use driveways where function leads.
- Exposed aggregate: the top layer of cement is washed away to reveal the stone. More tactile and visually interesting, but harder to clean and pricier to install.
- Stamped or patterned concrete: stamped looks like stone or pavers at a fraction of paver cost, but the tooling adds labor. Worth it on visible frontages; overkill for a back apron.
- Reinforcement choice: welded wire mesh is the baseline; #4 rebar on a 12- to 18-inch grid is more common on Culver City slabs over 400 square feet given the seismic zone and heavier soil movement. Rebar costs more but holds the slab together if cracking occurs.
- Concrete mix: a standard 4,000 psi mix handles a residential driveway; a 4,500 psi mix with air entrainment holds up better to coastal moisture cycling. We source from Sakrete-backed batch plants when the job calls for bagged prep, and from local ready-mix for full pours.
- Joint and sealant: control joints cost almost nothing at install and save you a cracked slab later. An expansion joint at the garage threshold with a quality sealant is standard, not optional.
See the difference
Before
After
Before
After
Before
AfterWhat Concrete Driveways & Concrete Work costs in Culver City, CA
Concrete driveway installation in Culver City lands between $4,500 and $12,000 for most homes. The low end is a small, simple slab with basic broom finish; the high end is a large, reinforced, exposed-aggregate or stamped pour with full demo and haul-off.
Five variables move that number:
- Square footage: most Culver City driveways run 400 to 600 square feet. Every additional 100 square feet adds roughly $600 – $1,200.
- Existing slab removal: full demo and haul-off of a thick old slab adds $1,000 – $2,500 compared with pouring over a clean base.
- Finish: broom is baseline; exposed aggregate or stamped adds 20 – 40% to the labor line.
- Reinforcement and mix: rebar and higher-psi mix push the job $400 – $900 higher.
- Permits and inspections: Culver City requires a permit for new or replaced driveways that affect the public right-of-way or drainage, and inspection adds a schedule line and a fee.
Every written estimate itemizes demo, base prep, reinforcement, concrete volume, finish, joint layout, and permit fees – and the number you see is the number you pay. What it doesn’t include: landscape restoration beyond the pour area, drainage improvements outside the driveway footprint, or relocation of utilities not identified during the site walk. Those are quoted separately before they ever start.
What Culver City homes specifically do to this job
Culver City sits in a coastal-adjacent basin with warm, dry summers and mild wet winters, and persistent ocean moisture works on concrete and the stucco around it. The bigger factor on older lots is the soil and the slab beneath it. In Carlson Park and Sunkist Park, the 1920s – 40s Spanish bungalows often have original driveways poured thin and with shallow footings that have heaved over decades. In Culver Crest, the hillside grade means drainage direction is a design question, not an afterthought – we set slope and control joints specifically so water moves away from the garage and the house, not under it. The city’s Cultural Affairs Commission design review can also apply when the driveway apron or visible frontage changes in the Carlson Park Historic District, so we check that before we demo. If the driveway project is part of a full Driveway & Pavers in Culver City scope, we coordinate the concrete and paver work together so the transition lines and grades match.
Serving Culver City, CA – Our Local Coverage Area
We serve Culver City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Concrete Driveways & Concrete Work in Culver City
Most jobs run 3 to 7 days from demo to final cure walkthrough, with vehicle traffic on the slab after 5 to 7 days of cure. The timeline assumes standard access and no surprise utility conflicts. Call (888) 427-1733 for a site-specific schedule.
Often yes – any new or replaced driveway that touches the public right-of-way, curb, or drainage requires a permit, and the inspection happens before the pour. We pull the permit and schedule the inspection as part of the job. Call (888) 427-1733 to confirm what your property needs.
Sometimes. If the existing slab is structurally sound and the height difference doesn’t cause a threshold problem, an overlay is possible, but most Culver City jobs we see have a slab that’s already cracked or heaved. Full replacement is more reliable and lasts longer. Call (888) 427-1733 and we’ll tell you which applies to your driveway.
Concrete driveway installation runs $4,500 – $12,000; a driveway replacement with full demo runs $5,000 – $14,000; and sealing after cure is $250 – $700. The variables are square footage, existing slab condition, finish, and reinforcement. Call (888) 427-1733 for an exact quote – estimates are free.
Every project is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right for two full years. That’s one of the longer workmanship guarantees in residential construction, and it’s written, not verbal. Call (888) 427-1733 to talk through the details.
Free on-site estimate for Concrete Driveways & Concrete Work in Culver City
We’ll measure the driveway, walk the drainage, check the garage threshold, and hand you a written line-item estimate – free, no pressure, no surprises on the invoice. Calls are answered by a live person 24/7, and technicians arrive background-checked and in uniform. Financing is available at 0% for 18 months, and projects over $10,000 get $1,000 off. Call (888) 427-1733 today to lock in your estimate.
Written by the team at Groundwork Construction Co.