Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Culver City: What It Costs and How Long It Takes
Door installation in Culver City typically runs $450 to $1,600 per exterior door and $250 to $900 per interior door, and most single-door jobs are finished in one day. A full house package of six to eight doors usually takes two to three days, with framing and trim work on day one and hardware, thresholds, and weather sealing on the final day. Call (888) 427-1733 for a free on-site estimate and we’ll give you a written line-item quote before anything gets ordered.
The Order We Work In, From Demo to Final Walkthrough
Door installation isn’t complicated, but it’s sequence-sensitive. Get the order wrong and you’re patching stucco or re-hanging trim a week later. Here’s how the five stages actually run in a Culver City house.
Stage 1: Measure, opening assessment, and material decisions (day 1, 1 to 2 hours)
We pull the existing door, check the rough opening for square and plumb, and inspect the framing behind the trim. In Culver City’s older homes this is where surprises show up: rotted sill plates under an entry door, termite damage in a jamb, or stucco that’s pulled loose from the frame. You make your final decisions here on door material, slab thickness, and whether you’re keeping the existing trim profile to match the rest of the house.
Stage 2: Opening prep and framing corrections (day 1, 2 to 4 hours)
Out-of-square openings get shimmed, planed, or reframed. We replace damaged jack studs and headers where we find them. If the door is going into a load-bearing wall as part of a new opening, that’s a header install and it changes the scope and the timeline. You’ll approve any framing addition before we proceed.
Stage 3: Door set and shimmed (day 1, 1 to 2 hours)
The new unit goes in plumb, square, and level, with shims packed tight at the hinge side and threshold. This is the stage where a three-degree error becomes a door that swings open on its own. We check reveal gaps on all four sides and test operation before moving on.
Stage 4: Insulation, sealing, and trim (day 1 into day 2, 3 to 5 hours)
Low-expansion foam and backer rod go in around the frame, then interior casing and exterior trim. Older Spanish bungalows present trim matching challenges here, so we plan that detail during stage 1 rather than guessing on the spot. Exterior doors get a threshold pan or sill seal.
Stage 5: Hardware, finish, and inspection (day 2 or 3, 1 to 2 hours)
Hinges get final adjustment, locksets and deadbolts get installed and tested, and weatherstripping is fitted so the door closes with a firm, even seal. You walk the job with us, test every door yourself, and we correct anything on the spot before we consider it finished.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Door selection drives the price more than labor does. Here’s what moves the number in a real Culver City job.
- Steel entry doors – the strongest, most secure option, and a good fit for a street-facing entry where you want the deadbolt to matter. They hold up to weather well but can dent, and the budget version shows it.
- Fiberglass entry doors – the sweet spot for most Culver City homes. They won’t dent, won’t rust, take stain or paint well, and mimic the wood look that suits a Spanish bungalow. Slightly more than steel, holds up longer.
- Solid wood doors – the right choice for a historic facade in the Carlson Park Historic District, where the exterior look actually matters to design review. Highest cost, needs periodic refinishing given the coastal moisture.
- Interior hollow-core – the standard for closets and bedrooms. Light, cheap, and fine everywhere the door isn’t abused.
- Interior solid-core – better for bedrooms facing a busy street, for sound control, and for rooms where the door gets a lot of use. Adds cost but far less rattle and a quieter house.
- Slab vs. pre-hung – a pre-hung unit comes with the frame and installs faster. A slab reuses your existing frame and costs less on materials, but only works if the existing frame is square and sound.
- Fire-rated doors – required between an attached garage and the living space, and required on some additions. Not optional, and we’ll tell you when you need one.
You’ll also pick hardware tier (builder-grade, mid-grade, or architectural), threshold style, and whether to match the interior casing to the rest of the house or update it while we’re in there. None of this is a pitch; it’s just the decision set you’ll be walked through.
What Door Installation Costs in Culver City, CA
Here’s the honest range for door work in this market. Line-item quote, no surprises.
- Interior door, hollow-core, installed: $250 to $600
- Interior door, solid-core, installed: $400 to $900
- Exterior entry door, steel or fiberglass, installed: $450 to $1,300
- Exterior entry door, solid wood, installed: $900 to $1,600
- Patio or French door set: $1,200 to $3,500 (see our wider Windows & Doors service)
- Door installation only, no door supplied: $200 to $500 per opening
Five things push a job from the low end to the high end. Size matters: an oversized or custom-width opening costs more in door, trim, and time. Existing condition matters: a rotted sill or termite-damaged jamb is a $200 to $500 add. Structural changes matter: cutting a new opening in a load-bearing wall adds a header, a framing inspection, and hours of finish work. Material grade matters: a solid wood door with an architect’s selected finish is nowhere near a builder-grade slab. Permit scope matters: a like-for-like door swap generally doesn’t require a Culver City permit, but a new opening, a change in door size, or a garage fire-rated door behind a converted space usually does.
A written estimate from us lists the door model and unit price, the labor, the trim and hardware, disposal of the old door, and any framing allowance. It doesn’t include unforeseen rot or termite damage we only find after demo, which is why we show you the number on site before we proceed rather than burying it in a change order. If the job is part of a full Windows & Doors in Culver City project, the estimate bundles together so you see the whole picture.
See the difference
Before
After
Before
After
Before
AfterWhat Culver City Homes Specifically Do to This Job
The doors in Culver City tend to fail in ways the building stock explains. The 1920s to 1940s Spanish bungalows clustered in Carlson Park and Sunkist Park were built with original wood jambs and thin stucco reveals, and eighty years of coastal moisture has done its work on the south and west-facing entries. Combine that with double-wythe clay tile roofs and original wood lath under stucco, and every door swap has a real chance of turning up lath-to-stud attachment failures or a sill plate that’s started to soften. It’s routine for us to find that the door that “just needs replacing” needs the jamb opened up first. The ocean air sitting in the basin doesn’t help, and the warm-dry-summer, mild-wet-winter swing means warping and sticking seasons alternate. Culver City is also a high seismic zone, sited near the Santa Monica fault, so every door we set is checked against the framing as part of normal work.
On the flip side, the design-review side of Culver City matters here. The Carlson Park Historic District’s Cultural Affairs Commission review can hold up even a minor facade change, and an exterior door swap counts. If your house is inside that boundary and the door faces the street, we factor the review timeline into the schedule rather than finding out halfway through. If you’re on Culver Crest, fire-resistant detailing on the exterior door is the right call given the wildfire-adjacent hills designation. And if your project turns into a bigger scope, we cover the wider work through our Culver City page.
Serving Culver City, CA – Our Local Coverage Area
We serve Culver City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Door Installation in Culver City
Most single-door installations finish in one day, and a house package of six to eight doors takes two to three days. The wildcard is existing-condition surprises behind the trim, which can add a half day for framing or stucco repair. Call (888) 427-1733 for a firm timeline based on your house, not an average.
A like-for-like door swap usually doesn’t require a Culver City permit, but a new opening, a change in door size, or a new garage fire-rated door behind a converted space typically does. We tell you which bucket your job falls into before scheduling and pull the permit if it’s required. Call (888) 427-1733 and we’ll walk you through it.
Yes, in almost every case. A door installation in the same opening doesn’t touch plumbing or structural work, and we only open framing when the existing jamb is rotted or out of square. If a new opening or a header is needed, we scope it separately so you know exactly what’s being added. Call (888) 427-1733 for a free site assessment.
Interior doors run $250 to $900 installed, exterior entry doors $450 to $1,600, and patio or French sets $1,200 to $3,500 depending on material and size. The material grade and existing condition drive the range more than the labor does. Call (888) 427-1733 for an exact quote – estimates are free.
Every door installation we complete is backed by our 730-Day Done Right Promise. If the fit, seal, or hardware isn’t right, we come back and make it right, and the door manufacturer’s product warranty backstops the unit itself. Call (888) 427-1733 to schedule your free estimate.
Get a Door Installation Estimate in Culver City
Free on-site estimates for door installation across Culver City, including Carlson Park, Sunkist Park, and Culver Crest. When you call (888) 427-1733, a live person answers, we book a time that fits your schedule, and we walk your doors with you, measure every opening, and hand you a written line-item quote with no surprises. If it’s a whole-house package, we can pair it with a Chain Link Fence in Culver City or a Vinyl Fence in Culver City if the yard work is going in at the same time. One contractor, one schedule, one written warranty.
Written by the team at Groundwork Construction Co.