Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Calabasas: What The Job Actually Involves
Custom & Geometric Windows in Calabasas means made-to-order units – arches, half-rounds, eyebrows, trapezoids, and radius-top assemblies built to a specific opening on a specific house, not swapped off a rack. Figure eight to fourteen weeks from first measurement to final trim-out, and expect $12,000 – $38,000 for a typical multi-opening package in this market. Call (888) 427-1733 and we’ll walk your openings on site, free.
Key Takeaways
- Custom shapes are built to the opening. Nothing gets ordered until templating is done and the frame is verified square.
- Most of the schedule is fabrication, not labor. You’ll wait on the factory far longer than you’ll wait on the crew.
- Calabasas hillside lots add real structural cost: headers, caissons, and slope review often outrank the windows themselves in the budget.
- Written line-item estimate, permits pulled, 730-Day Done Right Promise on the install.
How We Build Custom & Geometric Windows Into a Calabasas House
There’s a sequence to this work, and skipping a stage is how arched windows end up with daylight gaps and a year of caulk touch-ups.
Stage 1: Opening survey and templating (day 1)
We measure every opening twice, photograph the existing frames, and check for square. On an arch, we template the radius in place rather than trusting a homeowner’s sketch, because a wall that looks plumb from the living room is often two inches off at the head. You decide here whether you’re keeping the original openings or changing the geometry.
Stage 2: Structural review and engineering (days 2 – 10)
New or larger openings need a header sized by someone with a stamp. On Calabasas hillside homes this is where the real conversation happens: we look at how the wall carries load and whether the frame is tied into anything that needs a caisson or a shear upgrade. You approve the scope and the one key decision – match the existing architecture or go bolder.
Stage 3: Order, permits, and shop drawings (weeks 2 – 4)
Once the field measurements are locked, the manufacturer produces shop drawings for your signature. Read them. Every radius, every divided lite, every finish gets confirmed on paper. We pull the permit during this window, and we don’t order glass until the drawings are signed.
Stage 4: Fabrication (weeks 4 – 12)
The factory builds the units. Custom shapes aren’t stocked, so a half-round or a true arch line gets cut to the drawing and cured or tempered on its own schedule. You’ll get progress updates rather than silence. If you have HOA color requirements, this is when they get settled.
Stage 5: Install, trim, and inspection (3 – 5 days on site)
Frames are prepped, flashing and weather barrier detailed correctly, units set, shimmed, foamed, and trimmed. Glass goes in, hardware gets adjusted, and we schedule the inspection. You walk the job with us before the final invoice. Most installs with us finish in about a week of actual on-site work.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Actually Make
- Frame material. Wood holds a custom curve and takes a fine paint finish, but it needs periodic care in strong sun. Aluminum-clad wood gives you a wood interior and a maintenance-light exterior and is the usual pick for Mediterranean estates. Fiberglass handles heat movement well and is the quieter value option. Vinyl can’t hold most true radii.
- Glass package. Impact-rated laminated glass matters more than people assume in the Santa Monica Mountains foothills, and it pairs well with fire-hardening. Low-E coatings cut solar gain on west-facing walls. Tempered is required for large panes and anything near a door.
- Shape and lite pattern. A true radius costs more than a segmented arch made from straight units. Divided lites (grilles) can be internal between glass or applied outside – internal reads cleaner and costs more.
- Finish. Factory-baked finish on cladding outlasts field painting. For wood interiors, a clear sealer preserves the grain; paint is cheaper and more forgiving of an imperfect curve.
- Operation. Fixed units let you afford larger, more dramatic glass. Operable casement or awning inserts add cost and mechanical hardware but earn their keep in ventilation.
For the wider scope on the house, our windows & doors service covers everything beyond the specialty shapes.
What Custom & Geometric Windows Cost in Calabasas, CA
Plan on $12,000 – $38,000 for a custom and geometric package across several openings, with single radius units landing near $1,800 – $4,500 each before install. Here’s what moves the number up or down:
- Number and complexity of openings. One eyebrow window is a modest project. A gable wall of arched and trapezoidal units is a different budget.
- Existing condition. Rot behind the frame, stucco in poor shape, or a wall that wasn’t built square all add repair time before we can install anything.
- Structural work. New openings, enlarged openings, and headers on a sloped site pull in engineering and possibly foundation review – the single largest swing on a Calabasas job.
- Glass and finish grade. Impact-rated, Low-E, tempered, and internal grilles each add cost. Factory-baked finish costs more upfront and less over twenty years.
- Permit scope. A like-for-like shape swap runs a smaller permit than a structural opening change, and hillside review adds time to the front end.
A written estimate from us is line-item: units, glass, finish, trim, labor, engineering, permit, and disposal, with no change orders unless you approve them. What it won’t include upfront is undiscovered rot or a stucco repair we can’t see until the old frame comes out – those get priced and approved before we touch them.
See the difference
Before
After
Before
After
Before
AfterWhat Calabasas Homes Specifically Do to This Job
Calabasas sits in the Santa Monica Mountains foothills, and that single fact reshapes a window project. Hillside and canyon lots mean grade, retaining walls, and slope-stability review that a flatland crew never thinks about. Add the City’s hillside and oak-tree ordinances and post-Woolsey Fire rebuild standards, and a simple arched window package in a canyon home can turn into a permitting and geotechnical exercise before a single unit is ordered. In The Oaks and Calabasas Hills, we’re usually matching new geometry to existing Mediterranean and Spanish detailing, often on estates where an HOA has its own review before the City does. In the canyons, we work on 1960s-70s ranches and fire-rebuild custom homes where opening changes need to respect engineered foundations on sloped sites. The Very High Fire Hazard Severity Zone designation matters here too – Chapter 7A ignition-resistant assemblies, ember-resistant vents, and noncombustible trim around the opening all factor into what we specify. Coverage runs across ZIP codes 91302 and 91372 and beyond, so if your home is anywhere in Calabasas, we’ll come out and look at it.
Serving Calabasas, CA – Our Local Coverage Area
We serve Calabasas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Custom & Geometric Windows in Calabasas
Eight to fourteen weeks from field measurement to final inspection, with fabrication taking the bulk of that time and only about a week of it spent on site. Custom radius units are cut to order, so the factory schedule sets the pace. Call (888) 427-1733 for a benchmark on your specific openings.
Yes, in almost every case – and a like-for-like shape swap can run a lighter permit than an enlarged or new opening. Anything structural, including headers and opening changes on a hillside lot, goes through plan review. We pull the permit and schedule the inspection as part of the job.
Usually yes, if the new unit fits inside the existing rough opening with the same header. A true radius that’s wider or taller than the original frame is a structural change and gets engineering. We’ll tell you which category your project falls into during the survey.
Most packages run $12,000 – $38,000, with individual radius units costing roughly $1,800 – $4,500 before installation. Complexity, glass grade, finish, and structural work are the biggest drivers. Call (888) 427-1733 – estimates are free and we’ll itemize every line.
Every install we do is backed by our 730-Day Done Right Promise – if it isn’t done right, we make it right. Manufacturer glass and unit warranties run separately and we hand you the paperwork. If your project also touches the front of the house, homeowners often pair this with Concrete Driveways & Concrete Work in Calabasas so the elevations read together.
Schedule a Free On-Site Estimate
Custom and geometric windows are a considered purchase, not an impulse one, so start with a walkthrough. Call (888) 427-1733 and a live person answers – any hour, any day. We’ll measure your openings, talk through shapes and glass, and hand you a written line-item estimate. If you’re thinking bigger, view the full Windows & Doors in Calabasas scope, or pair a new front elevation with Asphalt Driveways & Resurfacing in Calabasas.
Written by the team at Groundwork Construction Co.