Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Agoura Hills, CA: Cost, Timeline, and What the Job Really Involves
An iron fence in Agoura Hills typically runs $3,500 – $9,000 installed, with most residential jobs landing between $4,800 and $7,200. A typical run of 60 to 120 linear feet takes three to five working days from layout to final coat, including footing cure time. The number moves with length, height, finish, gate count, and how much slope the crew is fighting on your lot. Call (888) 427-1733 for a free on-site measure and a written line-item quote.
How the Work Actually Runs, Start to Finish
A fence is a small project, but it’s not a casual one. Concrete footings, property lines, and slope stakes all happen before a single panel goes up. Here’s the real sequence we follow.
Stage 1: Site visit and layout (day one, roughly 90 minutes)
We walk the property line with you, measure the run, note grade changes, and flag anything buried that could interfere, from irrigation lines to old footings from a fence that came down years ago. This is when you decide the fence height, post spacing, and gate placement. Most homeowners in Agoura Hills pick a 4-foot ornamental run along the front and a 5- or 6-foot privacy-height iron or steel panel along the sides and rear.
Stage 2: Utility mark-out and permit check (one to three days)
Before anyone digs, we confirm the digging is clear of utilities and check whether your lot requires a fence permit through the City of Agoura Hills. Fences under six feet generally don’t need a building permit, but corner-lot sight triangles, HOA design review, and wildfire-zone rules can change that. You get the answer before a shovel touches the ground, not after.
Stage 3: Demolition and post setting (day two, most of the day)
If there’s an old fence, we pull it and haul it off. New posts go into concrete footings set per the spec sheet, typically 24 to 36 inches deep depending on soil and height. Footings cure overnight before panels go on, which is why the schedule runs three to five days rather than two.
Stage 4: Panel and gate install (day three, sometimes four)
Panels, pickets, and gates go on after the footings have cured. This is the stage where the level matters most, because a fence on a slope either steps cleanly with the grade or looks like it was installed by somebody who didn’t check. Ask about the step pattern before the crew starts.
Stage 5: Finish, hardware, and walkthrough (final day)
We touch up the finish coat, hang and adjust the hardware, check every gate latch and hinge, and walk the fence line with you. Any wobble, gap, or misaligned panel gets corrected before we call the job done. The 730-Day Done Right Promise covers workmanship for two full years, in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
What You’re Choosing Between: Iron Fence Options
Iron fence isn’t a single product. The choices you make at the estimate stage drive both the price and how the fence holds up over the next couple of decades.
- Wrought iron: Genuine forged iron, welded and hand-finished. Heavy, quiet, and the closest match to classic estate fencing. On the high end of the $3,500 – $9,000 range, and worth it for a home where the fence line is part of the property’s look.
- Tubular steel (ornamental iron look): The standard for most residential installs. Powder-coated, galvanized inside, and priced meaningfully lower than wrought iron without looking cheap. This is what we install most often.
- Aluminum iron-look panels: Lighter and rust-proof, but requires the right framing and looks lighter in person. Fine for low-height accent runs; less convincing at full privacy height.
- Finish: Powder coat in satin black or bronze holds up best against Santa Ana summer heat and canyon sun. Bare or painted finishes need re-coating every few years.
- Gate type: Manual swing gates are the default. Adding an automatic opener with rolling-code remotes is common on driveway gates and adds to the total, but it’s a decision to make at layout, not after install.
What an Iron Fence Costs in Agoura Hills, CA
Expect $3,500 – $9,000 installed for a residential iron fence in Agoura Hills. That range covers most of what we quote, with the variables below pushing toward one end or the other.
- Linear feet and height: 60 feet of 4-foot ornamental runs at the low end. 120 feet of 6-foot privacy-height steel with step-ups pushes toward the top.
- Slope and site access: Canyon lots off Kanan or Cornell can require hand-carrying materials up a grade where a truck can’t reach. That adds time, not deception.
- Gates and hardware: Each swing gate adds cost. An automatic opener with remote control adds more.
- Removal of an existing fence: Demo and haul-off runs separately from installation.
- Finish grade: Powder coat over galvanized steel is standard. Custom colors and special hardware cost extra.
Your written estimate spells out the linear footage, post depth, finish, gate count, and haul-off line by line. Upfront pricing, no surprises: the number on the estimate is the number on the invoice. Financing is available at 0% for 18 months, and projects over $10,000 qualify for $1,000 off.
See the difference
Before
After
Before
After
Before
AfterWhat Agoura Hills Lots Actually Do to an Iron Fence Job
Agoura Hills is not flat-valley work. The city sits in the Santa Monica Mountains’ foothills along the 101, and nearly every fence job here runs into slope, drainage, or brush-clearance questions before the first post is dug. A straight-line 100-foot run in Old Agoura’s horse properties can involve a grade change of several feet that has to be stepped cleanly, or a footing depth that changes to handle winter storm runoff on a canyon grade. Corner and through-lot properties along the 101 corridor also need sight-distance checked, since a well-intentioned 6-foot iron fence can obstruct driver views at a driveway apron.
The other factor is wildfire-code reality. Agoura Hills sits in a high fire-severity zone, and while fencing isn’t regulated the same way as a roof under Chapter 7A wildland-urban interface standards, the materials in and around the fence line are watched carefully by insurance and by the brush-clearance inspection that most hillside homeowners go through. Steel and iron are the right answer here for a lot of reasons. On the housing stock side, the 1960s – 80s ranch and split-level homes in Morrison Ranch and Old Agoura often have aging wood fences that have failed silently over a decade of dry summers and winter rain. We see property lines where the old fence post has rotted off at grade but the panel looks fine from the street. Sloped custom lots on the foothill side are more likely to need a retaining element or a footing redesign before the fence goes up. Homeowners often pair this with Patios, Walkways & Pool Decks in Agoura Hills when the whole backyard is getting reworked, or with ADU Design & Permitting in Agoura Hills when a new structure changes where the fence line needs to sit.
This is part of a full Fence Installation in Agoura Hills scope of work for a lot of clients, and it’s supported by our broader Fence Installation service. We cover all of Agoura Hills, including ZIP codes 91301 and 91376, Calabasas, Malibu, Topanga, and Santa Monica.
Serving Agoura Hills, CA – Our Local Coverage Area
We serve Agoura Hills and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Iron Fence in Agoura Hills
Most residential iron fence installations in Agoura Hills finish in three to five working days, including footing cure time. Slope, access, and gate count are the main variables. Call (888) 427-1733 for a specific timeline on your lot.
Fences under six feet tall typically don’t require a building permit through the City of Agoura Hills, but HOA design review, corner-lot sight distance, and hillside access rules can change that. We confirm before we dig. Call us and we’ll walk through your specific lot.
Yes. Sloped lots in Old Agoura, Morrison Ranch, and the canyon properties are the norm here, and the standard solution is a stepped panel design with footings that follow the grade rather than a flat run. The trade-off is slightly more material and labor. Call (888) 427-1733 to get an exact number for your grade.
Powder-coated steel and iron hold up well in Agoura Hills, since the finish resists the UV load and heat of a high fire-severity zone. Powder coat over galvanized steel is the standard specification we recommend, and it holds its look for years rather than months. Call us for the finish options on your project.
Residential iron fence in Agoura Hills runs $3,500 – $9,000 installed, with most jobs between $4,800 and $7,200. Workmanship is covered by our 730-Day Done Right Promise, and materials are warrantied per manufacturer. Call (888) 427-1733 for a written line-item estimate; estimates are free.
Get a Free Iron Fence Estimate in Agoura Hills
If you’re pricing an iron fence on an Agoura Hills lot, call (888) 427-1733. A live person answers 24/7, so you’re not waiting until Monday to leave a voicemail. We’ll schedule a free on-site measure, confirm the scope and permit situation, and hand you a written line-item estimate with financing options if you want them. No pressure, no surprises.
Written by the team at Groundwork Construction Co.