Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Calabasas: What the Job Actually Involves
An iron fence in Calabasas typically runs $3,500 – $9,000 for a standard front-yard or pool-enclosure run, and most installs take one to three days once materials and permits are in hand. The work means setting posts in concrete footings, welding or bolting panels to spec, and finishing the metal against rust before it ever sees a Santa Ana wind season. Call (888) 427-1733 for a free on-site estimate and a written, line-item quote with the number locked in.
How We Build an Iron Fence, Stage by Stage
Iron fencing rewards planning. The homeowners who get a one-trip, done-right result are the ones who settle layout and style decisions before anyone breaks ground. Here’s the sequence we follow on a Calabasas job.
Stage 1: Site visit and layout (day 1, about 2 hours)
We walk the property line, confirm where the fence sits relative to setbacks and any recorded easements, and mark the run. You decide the height (typically 4 ft for a front boundary, 5 – 6 ft around a pool), the panel style (picket, ornamental, or flat-top), and the gate locations. On canyon and hillside lots, this is also where we flag a slope change that will need stepped panels rather than one continuous level run.
Stage 2: Permits and HOA review (1 – 3 weeks, before any material is ordered)
Calabasas and its gated communities both have a say in what goes up at the property line. We assemble the submittal, confirm the fence meets rear and side setback rules, and coordinate with the architectural review committee where one applies. You approve the final drawing. Nothing gets ordered until this is cleared, which is why the calendar here is longer than the build itself.
Stage 3: Utility locate and footing prep (day 2)
Before a single post hole is dug, we call in the utility locate and confirm irrigation lines and low-voltage runs are clear. Footings go down at 24 – 30 inches depending on soil and fence height, set in concrete and left to cure. On sloped sites we pour at stepped intervals so panels follow the grade instead of cantilevering.
Stage 4: Panel and gate installation (day 2 – 3)
Posts get set plumb, panels get hung and aligned, and the gate is hung with hardware rated for the span. This is where a cheap install shows: racked gates, uneven pickets, welds that don’t line up. We check every hinge and latch before the crew rolls off.
Stage 5: Finish and final walkthrough (day 3)
We touch up the coating on field cuts, clean the site, and walk the finished fence with you. You get the written workmanship guarantee, and any punch-list item gets scheduled before we close out. Most jobs are finished in a single visit once permitting is done.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Iron fencing is a broad label. What you actually pick moves both the budget and how the fence ages in the California sun.
- Wrought iron (true forged): The traditional look, hand-forged with real heft. Highest cost, longest life, and the honest choice when you want an estate-grade gate and boundary. Suits the larger custom lots in the hills.
- Steel ornamental (tubular): The practical middle. Panels are formed from steel tube with powder-coat or galvanized finish, roughly half the cost of wrought iron, and it holds up well if the coating is quality. This is what most Calabasas homeowners choose for a front yard or pool enclosure.
- Aluminum look-alike: Lightest and most rust-resistant, but it dents and reads thinner up close. Better for decorative runs than for a security boundary.
- Finish: Powder coat lasts 10 – 15 years before it wants attention; galvanized plus paint runs longer. Matte black is the near-universal pick on these properties, so a custom color is a deliberate cost add.
- Height and gauge: Every extra foot and every heavier wall thickness raises the price. A 6 ft security run in heavier gauge can run 30 – 40% over a 4 ft picket run.
We’ll lay the trade-offs out side by side at the estimate so you’re choosing a material, not guessing at one.
What an Iron Fence Costs in Calabasas, CA
Most iron fence projects in Calabasas land between $3,500 and $9,000. Here’s what pushes a job to either end.
- Linear footage: The single biggest driver. A short 30 ft front run sits near the bottom; a full-perimeter 150 ft property climbs toward the top.
- Material and gauge: True wrought iron costs meaningfully more than steel ornamental; heavier steel adds labor and hardware cost.
- Terrain: Stepped panels, extra footings, and hillside setting on canyon lots add labor and cure time.
- Gates: A pedestrian gate is modest; a wide driveway gate with proper hardware or an opener is a separate line item.
- Demo and access: Removing an old fence, hauling off debris, or working around established landscaping adds cost.
A written estimate should spell out footage, material, gauge, finish, number of gates, footing depth, and permit fees as distinct line items. It typically does not cover landscape repair after excavation or an automatic gate operator; ask for those as add-ons up front so the final number doesn’t surprise you. Upfront pricing, no change-order games.
See the difference
Before
After
Before
After
Before
AfterWhat Calabasas Homes Specifically Do to This Job
Calabasas is hillside and canyon country, and fences here have to answer to that. Lots in The Oaks and Mulholland Heights are graded into slopes, so a property-line fence is rarely a flat run, and the footings have to be stepped and engineered rather than eyeballed. The city’s strict hillside review and protected coast live oak ordinances come into play when the fence line runs near a tree’s protected zone, which can mean a shift in layout before anything gets built. Add the Very High Fire Hazard Severity Zone designation and Chapter 7A standards, and metal is often the smart call where a combustible fence would run against a structure. Fire-rebuild custom homes in the canyons most often want a metal boundary that meets noncombustible expectations and survives Santa Ana wind loads. We see the same failure modes repeatedly: posts rusting at the ground line from poor sealing, gates racking because the footing was undersized, and powder coat failing early on box-store panels. That’s why we spec hardware and finish for a fifteen-year horizon.
Serving Calabasas, CA – Our Local Coverage Area
We serve Calabasas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Iron Fence in Calabasas
Installation itself is usually one to three days, but the full timeline from signed estimate to finished fence runs two to five weeks once you factor in permit review and HOA architectural approval. Call (888) 427-1733 to talk through your property’s specifics.
Often yes, especially for fences over a certain height or near a slope, and gated communities add their own architectural review on top. We handle the submittal and coordinate the review so you’re not chasing it yourself. Call for a quick read on your address.
In most cases yes. We work the post line carefully around established plantings, and the only excavation is at each footing. Larger removals or root-heavy zones we’ll flag at the site visit. Call (888) 427-1733 to schedule.
Most jobs run $3,500 – $9,000 depending on footage, material grade, terrain, and gate count. Heavier gauge, hillside footing work, and driveway gates push toward the high end. Call for an exact quote; estimates are free.
Our work carries the 730-Day Done Right Promise: if the install isn’t right, we come back and make it right. That covers workmanship; material warranties follow the coating or steel manufacturer. Ask on the call and we’ll spell out both.
Get Your Iron Fence Estimate in Calabasas
If you’re ready to put a number on an iron fence in Calabasas, call (888) 427-1733 and we’ll schedule a free on-site estimate. We measure the run, talk through material and gate options, and hand you a written line-item quote with the price held. A live person answers the phone around the clock. Every install is backed by our 730-Day Done Right Promise.
Homeowners often pair this with Fence Installation in Calabasas as part of a full boundary plan, and with Patios, Walkways & Pool Decks in Calabasas when the yard is getting a full rework. For newer ADU builds on the property, see ADU Design & Permitting in Calabasas, and explore our broader Fence Installation service or our full Calabasas coverage area.
Written by the team at Groundwork Construction Co.