Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Culver City: Cost, Timeline, and What’s Realistic
A tub-to-shower conversion in Culver City typically costs $3,500 – $10,000 and takes 5 to 12 working days once materials are on site. The job means pulling the tub, capping or reconfiguring the drain, waterproofing the wet zone, and setting a new shower pan, walls, valve, and glass. Small jobs on a sound 1950s rancho near Sepulveda stay near the low end; a full teardown on a Carlson Park Spanish bungalow pushes toward the top. Call (888) 427-1733 and we’ll price yours on site.
How we take a tub out and put a shower in, stage by stage
Every conversion follows the same skeleton. What changes is how much of the old house comes with it.
Stage 1: Measure and settle the layout (day 1, 1 – 2 hours)
We confirm the alcove dimensions, find the drain center and the valve wall, and check whether the existing rough-in is copper, PEX, or galvanized. This is where you decide the shower footprint: a standard 30×60 alcove keeps the plumbing where it is, a 36×60 or curbless walk-in usually means moving the drain, and that decision is the biggest cost fork in the whole job.
Stage 2: Demo and open the walls (days 1 – 2)
The tub comes out in pieces, the surround tile and backer come off to the studs, and we expose the valve, drain line, and the framing behind the wet wall. On pre-1945 Culver City bungalows this is where we find out whether the studs are true, whether there’s old drywall over lath, and whether a past remodel left a surprise behind the tub. We photograph everything before closing it up so you’ve got a record.
Stage 3: Rough-in and inspection (days 2 – 4)
New shower valve, drain relocation if you approved one, blocking for grab bars and glass, and any framing correction. If the scope touches plumbing or electrical beyond a like-for-like valve swap, this is the point where a Culver City permit and inspection enter the schedule. You don’t have to chase that part. We pull it and we meet the inspector.
Stage 4: Waterproofing and tile (days 4 – 9)
Cement board or a bonded waterproof membrane over the pan and walls, a flood test on the pan where required, then tile, grout, and a full cure before any glass goes near it. This is the slowest stretch and the one you don’t want rushed. Curing time is not negotiable, and it’s the stage where a cheap bid gets tempting and where leaks are born.
Stage 5: Fixtures, glass, and final walkthrough (days 9 – 12)
Trim, showerhead, drain cover, glass panels or a framed door, silicone at the seams, then a walkthrough where we run the water, check the slope, and show you where the shutoffs are. You get the written 730-Day Done Right Promise at handoff, not a handshake.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll actually choose between
- Acrylic or fiberglass surround: the fastest and cheapest path, roughly $3,500 – $5,500 installed. One molded piece, no grout lines, done in a few days. It reads as a builder-grade shower and it flexes over decades of use, so it suits a rental or a second bath more than a primary.
- Porcelain or ceramic tile over a waterproof membrane: the mainstream choice, about $5,500 – $8,500. You pick the tile, the grout, and the trim, and it’ll outlast the house if the waterproofing is right. Larger-format tile means fewer grout lines to keep clean.
- Natural stone (marble, travertine, slate): the top of the range, $8,000 – $10,000 and up depending on the slab. Beautiful and heavy, and it wants sealing. Porous stone in a shower is a maintenance commitment, so we say that up front rather than after.
- Prefab pan vs. a tiled mud-set pan: a prefab pan saves a couple of days and a few hundred dollars. A tiled pan lets you match the floor and get an exact curb height, which matters in a tight alcove.
- A curbless entry: add roughly $800 – $2,000 for the drain relocation and the recessed framing. Worth it if aging in place is on your mind, and it makes a small Culver City bath feel bigger.
- Framed vs. frameless glass: framed is the value option; frameless cleans up the sightline and costs a few hundred more. Either way, a glass panel instead of a full curtain is what makes the room feel like a rebuild instead of a swap.
On fixtures, Kohler is the name most of our Culver City clients land on for the valve and trim because parts stay available. Where a project grows into a full reconfiguration, that work often folds into our Bathroom Remodeling service.
What tub-to-shower conversion costs in Culver City, CA
Plan on $3,500 – $10,000. A like-for-like swap in a sound alcove sits at the bottom; a full gut with relocated plumbing, custom tile, and frameless glass lands at the top. Here’s what moves the number:
| Line item | Typical Culver City range |
|---|---|
| Demo, haul-away, and wall opening | $400 – $1,200 |
| Waterproofing and pan | $600 – $1,800 |
| Tile and setting materials | $900 – $3,000 |
| Valve, showerhead, drain, trim | $300 – $1,200 |
| Glass door or panel | $500 – $2,000 |
| Permit and inspection (where required) | $200 – $800 |
The variables that push you to $10,000 are size and layout, the condition behind the wall, plumbing or electrical relocation, material grade, and how much permitting the scope triggers. A 1920s Carlson Park bungalow with out-of-square studs and a cast-iron drain can add real labor; a clean 1960s rancho near Sepulveda usually won’t. Our written estimate is line-item and the number you see is the number you pay. Call (888) 427-1733 for an exact quote.
See the difference
Before
After
Before
After
Before
AfterWhat Culver City homes specifically do to this job
Culver City is two construction worlds in a few square miles. On former industrial land around Platform, Ivy Station, and Culver Steps, production work moves fast. A few blocks away, in Carlson Park, Culver Crest, and Sunkist Park, you’re dealing with 1920s – 1940s Spanish bungalows whose original framing and plumbing were never meant for a modern shower. In those houses we routinely find out-of-square studs, aging galvanized supply lines, and cast-iron drains that need relining or replacement before the new pan goes down. Ocean moisture in this basin works on wall cavities slowly, so old tub surrounds often hide soft wood we only see after demo. Carlson Park sits in a historic district with Cultural Affairs Commission design review, and while an interior shower swap usually clears that hurdle, anything touching a facade detail can slow the schedule. If your conversion is part of a full Bathroom Remodeling in Culver City, we plan the whole sequence so the shower isn’t the thing holding the room up. We work across Culver City and the surrounding ZIPs, and homeowners often pair an exterior-driven project with Metal Roofing in Culver City or Tile Roofing in Culver City while we’re already on site.
Serving Culver City, CA – Our Local Coverage Area
We serve Culver City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – tub-to-shower conversion in Culver City
Most conversions run 5 to 12 working days from demo to glass. Simple acrylic swaps finish near 5; a full tile gut with a relocated drain and a permit inspection runs 10 to 12. Weather rarely stops interior work, so the schedule is driven by curing time and inspection slots.
Often yes, especially when the drain moves, the valve wall changes, or electrical is touched. A pure cosmetic swap over existing rough-in may not require one. We check the scope against city requirements and pull what’s needed, then meet the inspector. Call (888) 427-1733 and we’ll tell you for your address.
Yes, and that’s the cheapest version of this job. Keeping the drain center and valve wall means a like-for-like rough-in and a standard 30×60 alcove shower. Moving the drain for a curbless entry or a wider footprint adds a few hundred to a couple thousand dollars and a day or two.
Typically $3,500 – $10,000, with most Culver City jobs landing in the $5,500 – $8,500 band for a tiled shower with glass. Tile choice, pan type, glass style, and any hidden plumbing repairs are what separate the low end from the high. Call (888) 427-1733 for a line-item quote.
Every conversion carries our 730-Day Done Right Promise. If something isn’t right, we come back and make it right, and that’s in writing at handoff. Background-checked technicians arrive in uniform, and calls reach a live person any time.
Get a free tub-to-shower conversion estimate in Culver City
Call (888) 427-1733 and we’ll set a free on-site estimate for your tub-to-shower conversion in Culver City. We’ll measure the alcove, check what’s behind the wall, lay out your options with real numbers, and hand you a written line-item quote. Financing at 0% for 18 months is available, and projects over $10,000 take $1,000 off. No pressure, no vague bids.
Written by the team at Groundwork Construction Co.