Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wood Fence in Culver City, CA: What the Job Actually Involves
A wood fence in Culver City typically runs $3500 – $9000 installed, with most residential lots landing in the $5500 – $7500 range, and a typical job takes two to four working days from demo to final walk. You’re buying posts set in concrete, cedar or pressure-treated boards, framing, a gate, and a finish, plus removal of the old fence. Call (888) 427-1733 and we’ll schedule a free on-site estimate so you’re pricing your actual yard, not a generic number.
How We Build a Wood Fence, Stage by Stage
The sequence matters more than most homeowners expect, because poor layout and shallow footings are what kill fences in this basin within five or six years. Here’s how a Groundwork wood fence actually runs.
Stage 1: On-site measure and layout (day one, 1 – 2 hours)
We walk the property line with you, confirm exactly where the fence goes, and flag anything that changes the plan: a shared property line with a neighbor, a slope at the rear of the lot, a sprinkler main or gas stub near a post hole. This is where you decide fence height, gate location and which side faces out. On the narrow lots common in Carlson Park, a few inches of line placement changes the whole feel of the yard, so it’s worth getting right before anyone digs.
Stage 2: Demo and disposal (day one, 2 – 4 hours)
Old fencing comes out, posts are pulled where feasible, and debris goes into a dumpster on site. If there’s an existing concrete mow strip or footing, we break it out. You’ll want to move vehicles and clear the side yard before we arrive; on a tight Sunkist Park lot, the fence line is often the only path to the back.
Stage 3: Post setting (day one into day two)
Posts go in 24 to 36 inches deep in concrete, deeper on sloped or sandy lots, and they need to cure before framing. That cure time is the main reason a wood fence isn’t a one-day job. We set posts plumb and on a string line so the finished fence reads straight from the street even if the ground rolls. You’ll confirm post spacing here, typically 8 feet, tighter for a privacy build with heavy boards.
Stage 4: Framing, boards and gate (day two or three)
Rails, pickets or horizontal boards, cap and trim go up, then the gate gets hung and adjusted. Gates are where cheap fences fail first, so we frame and brace ours to carry the swing without sagging. This is when you’ll see the fence take shape and approve the look before finish goes on.
Stage 5: Finish, cleanup and walkthrough (day three or four)
Stain or sealer goes on, hardware gets a final adjustment, and we walk the whole run with you, gate by gate, post by post. Any board that cupped or split during install gets swapped before we leave. The full scope, including finish work, falls under the 730-Day Done Right Promise; if something we built fails, we make it right. If you’re also reworking the front of the house, homeowners often pair a new fence with Paver Driveways in Culver City so the front yard gets done in one pass.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Wood Fence Options You’ll Choose Between
Most of the price swing in a wood fence comes from four decisions, and each has a real trade-off.
- Cedar vs. pressure-treated pine. Cedar is naturally rot- and insect-resistant, holds stain beautifully, and suits the Spanish bungalow look in this city. It costs more per linear foot. Pressure-treated pine is cheaper and structurally sound, but it needs re-sealing every two to three years in this coastal moisture and it can warp as it dries.
- Dog-ear pickets vs. board-on-board vs. horizontal. Dog-ear is the fastest and least expensive build. Board-on-board gives full privacy with overlapping boards and a heavier look. Horizontal boards read modern and handle grade changes well, but they need tighter post spacing and cost more to build.
- Post material. Ground-contact rated wood posts in concrete are the standard. Steel posts with wood infill cost more but won’t rot at the soil line, which is the failure point we see most on 15- to 20-year-old fences here.
- Stain vs. clear sealer vs. bare. A penetrating oil stain holds up best against ocean moisture; clear sealer needs reapplication. Bare wood grays within a season or two, which some homeowners like and others don’t.
We’ll bring samples so you’re choosing between real boards, not photos. For a covered arbor or privacy structure attached to the fence line, brands like Cover make components worth looking at.
What a Wood Fence Costs in Culver City, CA
Plan on $3500 – $9000 for a wood fence in Culver City, with most full-yard residential jobs landing between $5500 and $7500. What moves you toward the high end:
- Linear footage and height. A 60-foot side-yard fence sits near the bottom of the range; a full 150-foot perimeter at 6 feet runs toward the top.
- Existing condition. Pulling old posts set in deep concrete, breaking out a mow strip, or removing fencing tangled in ivy adds labor and disposal.
- Grade and access. A sloped rear lot on Culver Crest takes stepped panels and more posts. Tight side-yard access means hand-carrying materials, which adds time.
- Material grade. Cedar, board-on-board and horizontal builds cost more in materials than dog-ear pine.
- Gates and hardware. Each gate is a built unit with its own framing and hardware, not a cut-down panel.
A written estimate from us is line-item and upfront: footage, material, post and footing detail, gate count, finish and disposal, plus whether a city permit is required. What’s typically not included is any repair to a neighbor’s shared fence, corrections to a property line that needs a survey, and irrigation or utility relocation if we hit something underground.
See the difference
Before
After
Before
After
Before
AfterWhat Culver City Homes Specifically Do to This Job
In the Carlson Park Historic District, even a fence replacement can run into the city’s Cultural Affairs Commission design review if it faces the street or borders a historic structure, so we check the requirement before anyone orders material rather than after. The 1920s – 40s Spanish bungalows throughout Carlson Park, Culver Crest and Sunkist Park sit on small lots with tight side setbacks, which means fence lines often double as property lines and posts land close to mature trees, roots and old irrigation. Add persistent ocean moisture and the fence failure we see most in Culver City is rot at the post base and board cupping on the weather side; in the Culver Crest hills, the same exposure plus brush-clearance rules can call for non-combustible detailing near the fence line. Permitting for fences here is generally straightforward, but we confirm height and setback rules and pull the permit when one is required. We cover all four ZIPs, 90232, 90230, 90231 and 90233, and the surrounding neighborhoods on our Culver City service-area page.
Serving Culver City, CA – Our Local Coverage Area
We serve Culver City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Wood Fence in Culver City
Most wood fences in Culver City take two to four working days, with the post cure time built in. A small side-yard run can finish in two days; a full perimeter with multiple gates runs closer to four. We’ll give you a firm day count in the estimate so you can plan around it.
Culver City requires a permit for fences above the standard height limit, and historic-district properties may need design review. We check the rules for your specific lot and pull the permit when required; you don’t have to sort that out yourself. Call (888) 427-1733 and we’ll tell you what your property needs.
Yes, in most cases. We locate irrigation and utility lines before digging and route posts around them. If a post lands directly on a line, we adjust spacing and add a panel, which is far cheaper than relocating a line. It’s part of what the free estimate covers.
Wood fences in Culver City range from $3500 to $9000, with most residential jobs landing between $5500 and $7500. Footage, cedar versus pine, gate count and old-fence removal are what move the number. Call (888) 427-1733 for an exact quote; estimates are free.
Our workmanship is covered by the 730-Day Done Right Promise, and the materials carry their manufacturer warranty. If a post we set or a gate we hung fails within that window, we make it right. It’s one of the longest workmanship guarantees we stand behind, in writing.
Get a Free Wood Fence Estimate in Culver City
We’ll come out, measure your property line, walk the options, and hand you a written line-item estimate with the timeline. Call (888) 427-1733 and a live person answers, day or night. No voicemail, no waiting until Monday. If the fence is part of a bigger project, we can scope Fence Installation in Culver City alongside the driveway or landscaping, or point you to our Fence Installation service for the full range of what we build. For a driveway or hardscape finish, Concrete Driveways & Concrete Work in Culver City is the natural pair.
Written by the team at Groundwork Construction Co.