Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Manhattan Beach: Cost, Timeline, and What’s Involved
A tub-to-shower conversion in Manhattan Beach runs $3,500 to $10,000 and takes three to seven working days from demo to final walkthrough. The job means pulling the tub, updating the drain and valve to current standards, prepping and waterproofing the walls and pan, setting tile, and hanging new glass and fixtures. Most homeowners call us ready to price, not ready to buy. Call (888) 427-1733 and we’ll set up a free on-site estimate so you know exactly where your project lands.
How a Tub-to-Shower Conversion Actually Runs, Stage by Stage
This isn’t a swap-in-a-new-tub job. You’re changing what a wet area is built to do, so the sequence matters more than the finish selections.
Stage 1: Site visit and written scope (day 1, about 60 minutes)
We measure the alcove, check the existing valve and drain position, look at the wall studs behind the tile, and confirm whether the framing can carry a shower pan without modification. You leave with a line-item written estimate: demo, rough-in, waterproofing, tile, glass, fixtures, permit, and haul-away, each priced separately. If a hidden issue could push the number, we flag it now rather than surprise you mid-build.
Stage 2: Demo and opening the wall (days 1 – 2)
We protect the floor and any adjacent cabinetry, pull the tub, and remove the old surround back to the studs. On a 1950s beach cottage this often means cutting out a layer of drywall, backer, and tile that was set over the original framing. Half a day of dust, then the wall is open and we can see exactly what the plumbing is doing.
Stage 3: Valve, drain, and rough inspection (day 2)
If the existing valve is a two-handle setup, we replace it with a single-handle pressure-balance or thermostatic valve so you aren’t scalded when someone flushes a toilet. The drain gets re-set to a linear or center position that suits the new shower footprint. In most Manhattan Beach jurisdictions the rough plumbing is inspected before walls close, so we schedule that and don’t bury anything the inspector needs to see.
Stage 4: Waterproofing and tile (days 2 – 5)
A liquid or sheet membrane goes up along with a pre-sloped shower pan, and we flood-test it before a single tile is set. Then comes the tile and grout. This is where your material choice eats time: a large-format porcelain goes down faster than a mosaic, and a curbless entry with a fully tiled floor adds a day of detail work.
Stage 5: Glass, fixtures, final inspection (days 5 – 7)
Tempered glass panels and hardware go in, then the showerhead, valve trim, and drain cover. We run water, check the slope drains clean, wipe everything down, and walk the room with you. If the scope required a permit, the final inspection closes it out. You decide the glass style and fixture finish at the first visit; the tile itself you can pick up to two days before Stage 4.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Tub-to-Shower Conversion Options You’ll Choose Between
The material and configuration decisions drive most of the price swing. Here’s what actually matters and what each choice costs you in money and upkeep.
- Prefab acrylic pan and surround: the least expensive route, roughly $500 – $1,200 in materials. Fast to install, easy to clean with a spray, holds up fine for a rental or a spare bath. It reads as builder-grade in a house where the rest of the room has custom finishes, and it can crack at the drain if the subfloor flexes.
- Tiled shower with a traditional pan: the middle and most common path, $2,000 – $4,500 in tile and membrane. You pick the look, porcelain or ceramic, matte or polished, and it lasts. Grout lines need a yearly seal and a squeegee habit.
- Curbless, fully tiled shower: the premium end, $2,500 – $5,500 in materials and labor for the recessed pan. It suits aging-in-place planning and small alcoves where the curb eats floor space. Recessing the floor is structural work, so check the framing early.
- Glass: a frameless panel runs $900 – $2,200 installed. A framed unit or a curtain rod is a fraction of that. Frameless reads expensive and lets light through the room. It also means daily squeegeeing.
- Fixture finish: a Kohler or Delta valve and trim combo lands around $250 – $800 depending on finish. Salt air matters here. Brushed nickel and stainless hold their look far longer in coastal homes than polished chrome or blackened steel, which pit and fog first.
What a Tub-to-Shower Conversion Costs in Manhattan Beach, CA
Across Manhattan Beach, tub-to-shower conversions run $3,500 on the low end and climb to $10,000 at the top. The number is set by five things: the size of the alcove, the condition behind the old tile, whether plumbing or electrical has to move, the grade of tile and glass, and how much permitting the scope triggers.
- Low end ($3,500 – $5,500): a standard 60-inch alcove, no plumbing relocation, a prefab pan with a tiled surround, a framed glass door or curtain rod.
- Middle ($5,500 – $8,000): a tiled pan with a linear or mosaic floor, a new single-handle valve, and frameless glass.
- High end ($8,000 – $10,000): a curbless build with floor recessing, moving the valve to a different wall, large-format tile, and premium marine-grade hardware.
A written estimate from us lists demo, haul-away, rough plumbing, waterproofing, tile, glass, fixtures, and permit separately so you can see where the money goes. What’s typically not included: structural changes to framing if the floor won’t carry the recessed pan, and a building permit if your project needs one (we’ll tell you upfront rather than spring it later). Upfront pricing, no surprises, is how we run every job. That’s also why we back the work with our 730-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Manhattan Beach Homes Specifically Do to This Job
The coastal build stock and climate change this job in ways an inland contractor won’t anticipate. Manhattan Beach is dominated by custom single-family homes on small coastal lots, and a lot of what we open up sits in 1950s beach cottages on raised foundations, stucco and wood-frame walls, and the original cast-iron or galvanized plumbing. Open a wall in the Gaslamp area or west of Highland and you’ll often find the valve is a two-handle relic past its service life, which forces a rough-in upgrade you budgeted for as “maybe.” Salt-laden marine air eats galvanized fasteners and untreated steel, so we specify stainless and marine-grade hardware from the first day. Winter storms and marine humidity also mean the shower needs real waterproofing, not a painted-on shortcut. If your conversion is part of a wider project, our Bathroom Remodeling in Manhattan Beach page covers the full scope, and if you’re replacing the roof over that room at the same time, homeowners often pair this with Metal Roofing in Manhattan Beach or Tile Roofing in Manhattan Beach. We serve all of Manhattan Beach, ZIP codes 90266 and 90267 included, and you can see the wider scope in our Bathroom Remodeling service.
Serving Manhattan Beach, CA – Our Local Coverage Area
We serve Manhattan Beach and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Tub-to-Shower Conversion in Manhattan Beach
Most tub-to-shower conversions take three to seven working days from demo to final walkthrough. A prefab pan and tiled surround land on the fast end; a curbless, fully tiled shower with a rough-in plumbing change takes closer to a week. Build in a cushion for the inspection, since Manhattan Beach scheduling can add a day on each end. Call (888) 427-1733 to get a schedule estimate for your project.
If the drain, valve, or pan is changing, you likely need a plumbing permit, and the work has to pass inspection. A cosmetic swap that keeps the valve and drain position and only replaces the surround may not. We pull the permit and manage the inspection so you’re not the one chasing it down. Call (888) 427-1733 and we’ll tell you exactly what your scope triggers.
Yes, in most cases the existing valve and drain position can stay put and the alcove becomes a shower with no structural work. The exceptions: you want a curbless floor (framing has to recess), the old valve is a two-handle relic that fails pressure-balance code, or the drain is set for a tub and needs relocation to hit the pan slope. We confirm this at the site visit. Call (888) 427-1733 to get on the schedule.
Tub-to-shower conversions in Manhattan Beach range from $3,500 to $10,000, and the middle of that range lands around $6,000. Tile and glass grade, plumbing relocation, and whether you go curbless are the biggest levers. We put the number in writing, line by line, with no change-order surprises. Call (888) 427-1733 for your free on-site estimate.
Every conversion we install is covered by our 730-Day Done Right Promise: if it isn’t done right, we make it right. That covers our workmanship on waterproofing, tile, plumbing rough-in, and glass install for two full years. Manufacturer coverage on the valve and fixtures runs separately through the brand. Calls are answered by a live person 24/7, so you’re never waiting until Monday. Call (888) 427-1733.
Get a Free Tub-to-Shower Conversion Estimate in Manhattan Beach
If you’re ready to price a tub-to-shower conversion in Manhattan Beach, call (888) 427-1733. We’ll set up a free on-site estimate, walk the room with you, and hand you a written line-item quote the same day of the visit. You’ll know the scope, the timeline, and the exact number before you commit. Financing at 0% for 18 months is available, and projects over $10,000 get $1,000 off.
Written by the team at Groundwork Construction Co.