Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
What Custom & Geometric Windows in San Fernando, CA Involve
Custom & geometric windows in San Fernando are built to a specific opening rather than pulled from a stock catalog – arched, round, trapezoidal, angled, eyebrow, and half-round shapes that don’t fit a standard rough-in. Most jobs run two to four weeks from template to final trim, with a day or two of actual install, and land roughly in the $8,000 – $25,000 range depending on count and glazing. Call (888) 427-1733 to set up a free on-site estimate.
How We Build and Install Custom & Geometric Windows, Stage by Stage
This isn’t a truck-and-drop job. Shaped windows get measured, survived by a template, and made to fit one specific wall cavity. Here’s the sequence we run.
Stage 1: Site measure and template (day 1)
We measure the rough opening at multiple points, not just once, because a 1940s stucco bungalow is rarely square. For curved and angled shapes we pull a physical template – cardboard or lauan – so the shop builds to the exact radius. You decide here whether you’re matching existing trim profiles or going cleaner and simpler.
Stage 2: Design review and final sign-off (days 2 – 4)
We come back with the shop drawing: frame material, glazing, grille pattern, and finish. You sign off on the drawing before anything goes into production. This is the stage where a 3-inch change to a radius or a grille layout is cheap, and after the order is cut it isn’t.
Stage 3: Fabrication and permit (weeks 2 – 3)
Shaped units build in about two to three weeks. In parallel we pull the permit through the City of San Fernando’s own building department. Egress windows and any unit that changes the opening size need this step; that’s covered below.
Stage 4: Demo, framing, and set (day 1 of install)
We open the wall, check for dry rot and past termite or water damage, re-frame or add headers where structure requires it, and set the unit plumb and level with proper flashing. A lot of these jobs turn up old framing that needs repair – we tell you before we cut into it, not after.
Stage 5: Insulate, trim, seal, and inspection (day 2 of install)
We insulate the perimeter, install interior and exterior trim, seal and flash the exterior, then walk the city inspector through. You get a final walkthrough with us before we call it done. The whole thing is covered under our 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between for Geometric and Custom Windows
- Frame material: Wood is the most forgiving for curved and angled shapes and paints or stains beautifully, but it needs maintenance in San Fernando’s intense summer sun. Vinyl holds up with almost no care but is limited in radius and finish options. Aluminum handles tight radii and large spans best; fiberglass is the middle ground – dimensionally stable, low maintenance, and priced between the two.
- Glazing: Standard insulated glass handles most walls. Low-E and solar-control coatings make sense on the west- and south-facing walls that take the brunt of the Valley heat – it’s a modest upcharge and it matters here.
- Grille pattern: Straight grilles, true divided lites, or a simple single pane. True divided lites cost more and add character; for a round or arched unit, most homeowners pick a single pane or a simple radial pattern because fine grilles get lost in the curve.
- Trim and surround: Matching the home’s existing stucco key or trim profile keeps the addition looking original. Going modern with a clean reveal is the other path, and it’s often cheaper on older homes because there’s less custom millwork.
- Shape and count: A single arched transom over a front door is the most common request. A cluster of geometric units on a stairwell or great-room wall costs more because each shape is built to its own template.
What Custom & Geometric Windows Cost in San Fernando, CA
Most geometric and custom window jobs in San Fernando land between $8,000 and $25,000 for a project of several units. A single arched transom runs toward the low end; a cluster of trapezoidal and radius units with premium frame and glazing pushes to the high end. Here’s how we itemize.
- Single arched or round unit, standard frame and glazing: roughly $1,200 – $2,500 installed
- Multiple shaped or angled units, premium frame: roughly $3,000 – $6,000 installed each
- Framing and header work on an older opening: add $400 – $1,500
- Trim, flashing, and finish carpentry: add $300 – $900 per unit
- Permit and inspection fees: a few hundred dollars, charged at actual cost
What pushes a job to the high end: historic or highly irregular openings, large spans that need structural headers, premium glazing, and true divided lites. What’s included in a written estimate: template, fabrication, demo, framing repair to a stated allowance, install, trim, flashing, sealant, permit, and inspection. What typically isn’t: structural engineer fees if the opening is load-bearing, and any hidden dry-rot or termite repair beyond the allowance – we flag that on the estimate so it’s not a surprise. Our upfront pricing means the number you see is the number you pay. Call (888) 427-1733 for an exact quote; estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat San Fernando Homes Specifically Do to a Custom Window Job
San Fernando is one of the few LA-area cities that runs its own building department and plan check, not LA County or the City of LA. That’s a real factor here. Inspectors and plan checkers on a city of about 2.5 square miles know the contractors working in it, and a submittal that’s wrong gets bounced fast. We size and document every opening accordingly.
The housing stock makes it trickier. Most of what we work on is postwar and early-1900s bungalows and small stucco homes on tight mid-century lots – many with original wood-frame walls that have shifted over decades. An arched opening in a 1947 bungalow is rarely the shape the drawing says it is once the wall is open, so we template rather than trust the tape. The Valley’s heat and UV punish exterior trim and seals, so we spec sun-resistant finishes and re-seal on a schedule. Seismic exposure means any framing we add is strapped to current standards. If your custom window job is part of a Windows & Doors in San Fernando project across the whole house, we scope it together.
We’re an experienced crew and our technicians have up to 12 years of experience on shaped and geometric units. Our windows & doors service covers everything we do, and if you happen to be coordinating exterior work, homeowners often pair this with Concrete Driveways & Concrete Work in San Fernando or Asphalt Driveways & Resurfacing in San Fernando in the same project window. Learn more about Windows & Doors or check our coverage on the San Fernando page.
Serving San Fernando, CA – Our Local Coverage Area
We serve San Fernando and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Custom & Geometric Windows in San Fernando
Expect roughly two to four weeks from templating to final inspection. Fabrication of shaped units takes two to three weeks; the actual install is usually one to two days on site. The permit through the City of San Fernando runs in parallel. Call (888) 427-1733 for a timeline on your specific openings.
Yes, in most cases. Any change to the rough opening, any new egress window, and any structural framing all need a permit through the City of San Fernando’s building department, and a final inspection. Straight like-for-like swaps may be exempt; we confirm that on the estimate so you’re not guessing. Call (888) 427-1733 and we’ll walk you through it.
Sometimes yes, sometimes no. If the new unit fits inside the existing opening and the wall isn’t load-bearing, we install without touching plumbing or framing beyond the opening. If the shape is larger than the current hole or the wall carries load above it, we add a header and that’s a structural change. We tell you which before we cut.
Most projects run $8,000 – $25,000 for several units. A single arched transom typically runs $1,200 – $2,500 installed; a cluster of trapezoidal or radius units with premium frame and glazing runs $3,000 – $6,000 each. Call (888) 427-1733 for an exact quote – estimates are free.
Our 730-Day Done Right Promise covers workmanship for 730 days – if it’s not done right, we make it right. Manufacturer warranties on the frames and glazing carry on top of that. Call (888) 427-1733 if you’d like the written terms before your estimate.
Get a Free Estimate for Custom & Geometric Windows in San Fernando
If a shaped or angled window is on your list, we’ll come measure the opening, pull a template, and hand you a written line-item quote – fixed, with the structural allowance spelled out, not a vague range. Call (888) 427-1733 to schedule your free on-site estimate. A live person answers that line around the clock, and we’ll get you on the calendar. $1,000 off projects over $10,000, and 0% financing for 18 months.
Written by the team at Groundwork Construction Co. of Los Angeles.