Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Marina del Rey: What the Job Actually Involves
Custom and geometric windows in Marina del Rey typically run $8,000 – $25,000 installed, depending on the count, the shapes, and how much framing the existing wall allows. Most jobs we quote land in three to five weeks from template to final inspection: roughly two weeks for fabrication on the angled or arched units, and two to four days on site for teardown and set. The work is narrow and specific, which is why it’s worth a real conversation before a deposit. Call (888) 427-1733 and we’ll walk the site.
This isn’t the shopping-center window-replacement world. A geometric window is a build decision as much as a product decision. The angles have to be templated to your wall, the header has to carry the load the old opening carried, and on the marina’s 1960s – 1980s condo stock, the framing you find once the stucco is off rarely matches what the drawings promised.
How We Run a Custom & Geometric Windows Project
Every job follows the same five stages. The durations below are what we actually schedule, not a best case.
- Stage 1 – Site walk and measurements (day 1, 60 – 90 minutes). We measure the existing opening, check the header, and photograph the wall assembly on the interior and exterior. You decide which openings you’re targeting and whether the geometry is a true arch, a half-round, a triangle, a trapezoid, or a stacked transom above a rectangle. Bring your HOA’s exterior-change form if you have one; we’ll read it on site.
- Stage 2 – Template and drawing sign-off (days 2 – 10). For angled and arched units, a field template or a laser-measured drawing goes to the fabricator. This is where you lock the glass package, frame finish, and hardware. Expect a signed submittal before anything is ordered. Condo jobs on Admiralty Way usually need an architectural review signature here, and that step alone can add a week if the board meets monthly.
- Stage 3 – Fabrication (about 10 – 14 days for geometric units). Rectangular units come faster; a true radius or a mitered-corner frame does not. We confirm the delivery date in writing before Stage 4 begins.
- Stage 4 – Removal and set (2 – 4 days on site). Flashing, sill pan, and frame go in first, then the unit, then the interior trim and exterior sealant. Any rot in the rough opening gets replaced during this window, and we tell you the cost the same day we find it rather than folding it into a change order later.
- Stage 5 – Inspection and closeout (same week). Where the work touches the building envelope or changes an opening, we pull the permit and schedule the inspection. Final walk, written closeout, and the 730-Day Done Right Promise is attached to the paperwork in plain language.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between on a Geometric Window Project
The frame and glass package is where most of the decisions live, and the trade-offs are real.
- Wood-clad frames (Andersen, Marvin): the classic choice for arched and angled units because the corner joinery holds true and the frame can be milled to a genuine radius. Warmer inside, paintable to your trim, but the exterior cladding has to be corrosion-grade for salt air or the fasteners and cladding edges will show rust within a few seasons.
- Aluminum with a thermal break: thinner sightlines, which reads cleaner in the marina’s contemporary towers and infill townhomes. Needs a marine-grade finish (anodized or a coastal-rated powder coat), not the standard inland coating, or the salt fog off the water takes it down inside a decade.
- Fiberglass and composite: stable dimensionally, so a trapezoid or a long narrow transom won’t rack out of square. Suits the 1970s stucco condos where the wall moves with the marine layer. Limited finish options, which matters if your HOA has a color rule.
- Glass package: laminated glass for wind-driven rain and some security value; low-E for condensation control on the cool, damp side of a cold-framed wall; and for angled units, the glazing has to be specified for the shape, not cut from a standard sheet.
- Hardware and operation: fixed units are the simplest and cheapest for true geometry; operable awning or casement hardware in a non-standard shape costs more and needs a good weather seal, so we tell you honestly where a fixed panel will serve you better.
What Custom & Geometric Windows Cost in Marina del Rey, CA
Plan on $8,000 – $25,000 for the job, with rectangular custom runs sitting at the low end and a mix of true radius, angled, and stacked geometric units toward the top. What moves the number:
- Count and shape complexity: one arched feature window might sit at $3,000 – $6,000; a whole façade of trapezoids and a half-round transom will run well past $20,000.
- Existing condition: if the rough opening is sound, the job stays in range. Rot, a sagging header, or a 1970s stucco wall that’s cracked along the corner adds framing and stucco-repair work at the high end.
- Structural change: enlarging an opening, adding a header, or going floor-to-ceiling means structural work and inspection – that’s the biggest single push toward the top of the range.
- Material grade: standard-clad wood at the low end; marine-grade aluminum or a premium clad package at the high end.
- Permit scope: a like-for-like replacement may not need one, but any change in opening size or an envelope-touching install does – we include the permit and inspection in the written quote.
A written estimate here lists units, glazing, hardware, flashing and sealant, framing repair allowance, permit and inspection, and disposal. What it doesn’t cover unless we state it: interior paint beyond the trim line, HOA fees, and any structural repair found after demo.
See the difference
Before
After
Before
After
Before
AfterWhat Marina del Rey Homes Do to This Job Specifically
Nearly every project here is a waterfront-adjacent remodel, and the coastal environment drives the spec more than the design taste does. Salt air attacks fasteners and metal faster than any inland owner expects; the marine-layer damp causes condensation on cold-framed walls and attic-side surfaces; and the wide low eaves and flat roofs common to the marina’s 1960s – 70s apartment architecture trap moisture where an inland house would dry out. In the marina, exterior fasteners last half as long – a gasket or window screw on a 1970s Admiralty Way condo is often already rust-stained, and we spec stainless and marine-grade hardware from the start rather than correcting it two years in.
Buildable land is scarce here, so the work is dense multifamily and condo renovation, plus the occasional surviving 1950s-era bungalow off Washington Boulevard. That mix means a geometric window project usually lives inside a condo association’s exterior-change rules, with a board review and often a coastal-zone consideration, rather than a standard single-family permit path. It’s a different sequence than a Santa Monica or Culver City job, and we plan the schedule around it. For the rest of the envelope scope, see our Windows & Doors in Marina del Rey page.
Serving Marina del Rey, CA – Our Local Coverage Area
We serve Marina del Rey and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Custom & Geometric Windows in Marina del Rey
Most jobs take three to five weeks from template to final inspection, with roughly 10 – 14 days of that in fabrication for the geometric units and 2 – 4 days on site. The variable is the condo association review, which can add a week if the board meets monthly. Call (888) 427-1733 to get a schedule against your actual dates.
You do if the opening size changes, if the header or structure is affected, or if the install touches the building envelope – which most geometric work does. Like-for-like replacement in the same opening sometimes doesn’t, but the condo association’s architectural review usually applies either way. We pull the permit and pass the inspection as part of the written quote, and we’ll confirm the path for your address on the site visit.
Often yes, if we’re setting a shaped unit into an existing opening that’s functionally the right size. Plumbing can’t move without a bigger scope anyway, and a header change is what forces structural work. Where the shape doesn’t fit the current opening, we tell you upfront what the framing work adds before you commit. Call (888) 427-1733 and we’ll give you the number.
Plan on $8,000 – $25,000 installed, driven by shape complexity, existing condition, structural change, material grade, and permit scope. A single arched feature window can run $3,000 – $6,000; a full façade of geometric units runs past $20,000. Call (888) 427-1733 for an exact quote – estimates are free.
Every custom & geometric window install is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space, and it’s in writing on the closeout. Manufacturer coverage on the unit and glazing is separate and passes to you; we hand over the paperwork at final walk.
Book a Free Estimate for Custom & Geometric Windows in Marina del Rey
A free on-site estimate for custom & geometric windows in Marina del Rey starts with a call to (888) 427-1733. A live person answers, 24/7, and we book a site walk that fits your schedule and the condo association’s access rules. On site, we measure the openings, check the framing, and read your HOA’s exterior-change form with you. You’ll get a written line-item quote with the permit and inspection included, and the price you see is the price you pay. Many of these jobs are part of a larger envelope project, so ask about our Windows & Doors service while you’re on the call.
Homeowners across Marina del Rey pair this scope with exterior work – a new sill and threshold often connects to Concrete Driveways & Concrete Work in Marina del Rey where a stoop or walkway is in the plan, or to Asphalt Driveways & Resurfacing in Marina del Rey where an approach apron needs to be rebuilt while the crew and equipment are already on site. Either way, you’re dealing with one schedule and one written guarantee, and the 730-Day Done Right Promise covers the work from the first measurement to the final walk.
Written by the team at Groundwork Construction Co.