Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Los Angeles, CA: What It Takes and What It Costs
Door installation in Los Angeles runs roughly $950 to $4,800 per opening, with most single-door replacements landing near $1,600 all-in, and a typical opening takes one to two days once the door is on site. Custom sizes, structural changes, or fire-rated requirements in hillside and soft-story buildings push that higher. Call (888) 427-1733 and we’ll walk your specific door, wall, and permit picture and give you a written, line-item number before anyone swings a hammer.
How a Door Installation Actually Runs, Start to Finish
Door installation is one of those jobs where the sequence matters more than the sales pitch. Here’s how we run it, and where you make the calls.
Stage 1: Measure and site check (day 1, about an hour)
We measure the rough opening, check the wall for plumb and square, and confirm what’s behind the trim: stucco, plaster, drywall, or the original 1920s redwood framing that shows up in so many Craftsman bungalows around Los Angeles. You decide the swing direction, the hardware finish, and whether we’re keeping the existing casing or replacing it. If the wall is out of square, we flag it now, not after the door is ordered.
Stage 2: Order and lead time (3 to 8 weeks depending on spec)
Stock slab and pre-hung doors in standard sizes move fast. A custom size, a specific wood species, or a fire-rated assembly takes longer. You approve the final spec sheet and the hardware before we place the order. This is the stage where a rushed decision costs the most money later.
Stage 3: Demo and rough opening prep (half a day)
We pull the old door, trim, and threshold, then inspect the framing and sill for rot or water damage. In a lot of Los Angeles homes, a door that’s been leaking for a decade hides soft framing underneath. If we find it, we show you and price the repair before we proceed. You get a photo and a number, not a surprise on the final invoice.
Stage 4: Set, shim, and seal (day 2, most of the day)
The door goes in, gets shimmed and plumbed, and the hardware is fitted. We flash and seal the exterior side with the right flashing detail for our sun-and-wind climate, then insulate the gaps. Most standard door installations are finished in a single day on site; a custom or structural install can run into a second.
Stage 5: Trim, finish, and walkthrough (same day or next)
Interior casing goes on, we touch up, and we walk the door with you: swing, latch, weather seal, and a check that the threshold drains away from the house. That last point matters more than people think in a city that gets dry for months and then dumps rain on us in a week.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Choosing the Door: What You’re Actually Picking Between
The door you pick drives most of the budget. Here’s the honest trade-off on each type.
- Fiberglass entry doors: The best value for most Los Angeles homes. They hold up against sun and dry heat, won’t warp like wood, and come in realistic wood-grain textures. Expect a mid-range cost and a long service life.
- Steel doors: Strong and secure, good for a side or service entry. The trade-off is that steel dents and can rust at the bottom edge if water sits on the threshold, so the flashing detail has to be right.
- Wood doors: Beautiful on a Spanish Colonial or Craftsman front, and they take a stain or paint finish no other material matches. They need periodic refinishing, and in our climate that means attention every few years.
- Sliding and glass-panel doors: The right move for a patio opening off a rear living room. These cross over into the wider Windows & Doors in Los Angeles scope, so we’ll scope them with the rest of the wall if that’s where your project is heading.
- Hardware and locksets: A separate line item and a real one. A quality lockset, deadbolt, and hinges can add a few hundred dollars, and on an exterior door you don’t want to cheap out here.
We stock and specify through established manufacturer partners, including Andersen and Marvin for glazed units, so you’re choosing from verified quality rather than whatever’s on a shelf. Homeowners doing a larger exterior refresh often pair a door install with Vinyl Fence in Los Angeles or a Chain Link Fence in Los Angeles to finish out the property line at the same time.
What Door Installation Costs in Los Angeles, CA
Most door installations in Los Angeles fall between $950 and $4,800, with a typical single exterior replacement around $1,600. Here’s what moves you toward the low or high end.
| Line item | Typical range |
|---|---|
| Interior door install (standard slab, pre-hung) | $250 – $750 |
| Exterior entry door install (fiberglass or steel) | $950 – $2,400 |
| Custom wood or premium entry door | $1,800 – $4,800+ |
| Door hardware and lockset | $150 – $600 |
| Framing or rot repair (if uncovered) | $300 – $1,500 |
Four things push the number:
- Size and swing. A standard 32″ interior door is the cheapest install. A 6-foot custom opening or a new rough opening costs more because framing changes.
- Wall condition. Plaster walls in older homes, out-of-square openings, and rot all add labor.
- Material grade. Fiberglass versus custom wood can double the door cost alone.
- Structural or fire-rated scope. Any change to a load-bearing header or a fire-rated door in a garage or soft-story building adds inspection and engineering.
Your written estimate lists the door, hardware, labor, finish, and any repair line by line, and it states the scope of permits if one is required. What it won’t cover is a surprise rot repair we find mid-job, because we price that only after we see it. One number, no change orders on the agreed scope. Every install is backed by our 730-Day Done Right Promise, so if something’s off in the first two years, we come back and make it right.
See the difference
Before
After
Before
After
Before
AfterWhat Los Angeles Homes Specifically Do to This Job
Los Angeles isn’t one housing stock, and door installation reacts to that. On the flats you’ll find 1920s-40s Spanish Colonial and Craftsman bungalows, and their plaster walls and original redwood framing are a different install from the postwar 1950s-60s stucco tract homes out toward the Valley. In Koreatown, the classic ‘dingbat’ apartment buildings with tuck-under parking are being retrofitted under the Soft-Story Retrofit Ordinance, and that work regularly touches shared entries and garage doors. Anything in the Hollywood Hills or Santa Monica Mountains hillsides gets pier-and-grade-beam foundations, so a wall you’re opening may be sited with unusual framing and a slope detail underneath it.
Permitting is a real factor. The city requires permits for structural door changes, fire-rated assemblies, and most exterior door replacements that alter framing or the rough opening, and some hillside work also has to answer to WUI ignition-resistant detailing under fire-zone rules. We pull the permits and schedule the inspections as part of the scope. What we see most often on older Los Angeles doors: sun-baked seals, rotted thresholds from years of dry-then-wet cycles, and out-of-square openings in stucco walls that need reframing. We cover Los Angeles and the neighboring communities like Culver City, Santa Monica, Marina del Rey, and El Segundo.
Serving Los Angeles, CA – Our Local Coverage Area
We serve Los Angeles and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Door Installation in Los Angeles
A standard door install takes one to two days on site, with three to eight weeks of lead time for the door itself if it’s custom or a specific finish. Stock doors in standard sizes move faster. Call (888) 427-1733 for a timeline on your specific door.
You need a permit if the job changes framing, alters the rough opening, or involves a fire-rated assembly, and many exterior replacements qualify. A simple swap in the existing opening often doesn’t. We confirm permit scope during the estimate and pull it as part of the job. Call (888) 427-1733 and we’ll tell you which side your project falls on.
Yes, in most cases. Replacing a door in the existing opening doesn’t touch plumbing, and structural changes are rare unless the size changes or the wall is out of square. When a header does need work, we price it as a separate, visible line.
Most jobs land between $950 and $4,800, with a typical exterior replacement near $1,600. Custom wood, fire-rated assemblies, and repair work push toward the high end. Call (888) 427-1733 for an exact quote; estimates are free.
Every door installation we do is covered by the 730-Day Done Right Promise, one of the longer workmanship guarantees in residential construction. If the install isn’t right, we return and fix it, and the manufacturer’s warranty on the door and hardware sits on top of that.
Get a Free Door Installation Estimate in Los Angeles
When you call (888) 427-1733, a live person answers, any hour, any day. We’ll ask about your door, the wall it’s going into, and whether you’re changing the size or the framing. Then we schedule a free on-site estimate and hand you a written, line-item price with the permit scope spelled out. Our technicians have up to 12 years of experience on door work, and every project is backed by the 730-Day Done Right Promise. Call today to get started.
Written by the team at Groundwork Construction Co.