Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Malibu, CA: What It Takes and What It Costs
Metal roofing in Malibu typically runs $15,000 to $40,000 for a full installation, with most hillside and bluff-edge homes landing in the $22,000 to $34,000 range once fire-rated assemblies and coastal-grade fasteners are factored in. A straightforward replacement takes three to six working days on site, but the permit path is the real schedule driver here: Coastal Development Permits and WUI fire-hardening review can stretch pre-construction by eight to fourteen weeks. Call (888) 427-1733 for a free on-site estimate.
How a Metal Roofing Job Actually Runs, Stage by Stage
Most homeowners picture roofing as a single blur of hammering. A metal install is closer to a five-act sequence, and knowing where you’ll be asked to make a decision keeps you from getting cornered mid-job.
Stage 1: Site inspection and geotechnical reality check (1 day)
We start on the roof deck and in the attic, checking sheathing condition, rafter spacing, and existing flashing. On Malibu bluff lots we also look at how the current roof ties into the drainage plane, because steep terrain means water leaves fast and any weak point shows up as erosion at the foundation line. You’ll get a written condition report before anyone orders material.
Stage 2: Permitting and coastal review (8 – 14 weeks, and yes, that’s normal)
This is where Malibu projects stall if the contractor doesn’t know the drill. A metal roof changes the fire classification and often the roof profile, both of which trigger WUI review under the fire-hardening codes that govern hillside parcels. If the home sits in the coastal zone, a Coastal Development Permit may be required before work begins. We pull the permits and handle the submittals; you sign and wait. This is the stage where cheaper bids quietly fall apart, so check that permitting is included, not billed later.
Stage 3: Tear-off and deck prep (1 – 2 days)
Old roofing comes off down to the sheathing. Any rotted decking gets replaced and recorded; on mid-century beach bungalows along the PCH frontage we often find original skip sheathing that needs a solid substrate laid over it before metal panels can be fastened. Ember-resistant vents get installed at this stage, not retrofitted later. You’ll see photos of every deck repair before the new roof goes on.
Stage 4: Underlayment, panels, and trim (2 – 3 days)
High-temp underlayment goes down first, then panels run from the eave up so laps shed water the right direction. Ridge caps, sidewall flashing, and valance trim close the edges. This is the stage where the crew’s pace tells you whether you hired the right outfit: rushed panel runs and skipped fasteners leak within two seasons. Fasteners here are corrosion-resistant, not standard steel, because salt spray eats the wrong hardware fast.
Stage 5: Final inspection and walkthrough (half a day)
We walk the roof with your inspector, then walk it with you: gutters, flashing terminations, penetration seals, and the warranty paperwork in hand. Nothing gets signed off until it passes.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Metal Roofing Options You’ll Choose Between
Metal is a category, not a product. The pick you make here drives both cost and lifespan.
- Standing seam (hidden fastener): the top-end call, with clean vertical lines and the fewest penetration points. Best lifespan, best wind performance, highest price.
- Exposed-fastener panels (screw-down): lower cost per square, faster install, but every fastener is a future leak point. Fine for outbuildings, rarely worth it on a primary residence.
- Stone-coated steel: metal panels pressed to mimic tile or shake. Popular on Malibu homes where a design review board or HOA expects a traditional profile but the owner wants Class A fire performance and lighter weight.
- Aluminum vs. steel: aluminum shrugs off salt air better than galvanized steel, which matters on properties close to the surf line. Steel runs cheaper and is stronger, so it wins on inland canyon lots.
- Kynar 500 finish vs. standard paint: the upgraded finish holds color under UV and marine exposure for decades; standard paint chalks and fades. On a roof you’ll keep for 40 years, the finish upgrade is cheap insurance.
- Panel profile and gauge: thicker gauge and taller seams cost more but handle Santa Ana wind uplift better.
What Metal Roofing Costs in Malibu, CA
The market range for metal roofing in Malibu is $15,000 to $40,000. Here’s what pushes a job toward the low versus high end:
- Roof size and pitch: a low-slope 1,200 sq ft bungalow roof sits near the bottom of the range; a steep multi-gable hillside roof sits near the top.
- Access: canyon roads like Latigo and Encinal are the only route to many hillside job sites, so material deliveries and staging have to be scheduled around narrow, winding grades. Steep driveways add labor and sometimes crane cost.
- Existing deck condition: rotted sheathing, skip sheathing, or a tear-off that uncovers structural repairs adds cost once the deck is open.
- Material spec: aluminum with a premium finish sits above galvanized steel; stone-coated steel sits in the middle.
- Permit scope: coastal review, structural upgrades triggered by the new roof load, and WUI fire-hardening requirements all add line items.
A written estimate from us lists tear-off, decking, underlayment, panels, trim, fasteners, gutters, permits, and inspection. What it doesn’t cover unless spelled out: structural repair uncovered mid-job, skylight replacement, and any change order (which we price in writing before we touch it, per our no-surprises approach).
See the difference
Before
After
Before
After
Before
AfterWhat Malibu Homes Specifically Do to This Job
Malibu construction is defined by the Santa Monica Mountains meeting the Pacific, and that geography shapes a metal roof before a single panel is cut. Nearly every project here is a hillside or bluff-edge build, which means geotechnical slope stability reports, coastal development permits, and fire-hardening requirements all run alongside the roofing scope. The housing stock we work on most is a split between mid-century beach bungalows along the PCH frontage and larger contemporary hillside homes on canyon and bluff lots, and the older bungalows are usually the ones with a rusted-out original roof and a sagging deck underneath it.
The marine layer, salt spray, and Santa Ana wind events drive material selection directly: corrosion-resistant fasteners and marine-grade exterior hardware aren’t upgrades here, they’re baseline. The fire-prone chaparral interface means Class A roof assemblies and ember-resistant vents are standard, and that’s a code issue, not a preference. Winter rain on steep terrain raises drainage and erosion-control concerns on nearly every site we inspect. Coastal Commission approval can add months before foundation work (or roof work connected to it) begins, so a metal roofing timeline that looks generous on paper is usually the honest one.
If the metal roof is part of a full Roofing in Malibu scope that includes gutters and accessories, we coordinate the trades so you’re not managing three contracts. And because we cover the whole of Malibu alongside neighboring areas like Topanga and Calabasas, scheduling across different permit jurisdictions is routine for us.
Serving Malibu, CA – Our Local Coverage Area
We serve Malibu and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Malibu
On-site work runs three to six working days for most homes, but plan on eight to fourteen weeks of permitting and coastal review before day one. The clock that surprises homeowners is the permit clock, not the build clock. Call (888) 427-1733 and we’ll walk through the timeline for your specific parcel.
Yes. A metal roof replacement requires a building permit, and parcels in the coastal zone or in the WUI fire-hazard area often require additional review. We pull the permits and manage the inspections; you don’t file anything yourself. Call (888) 427-1733 for a free estimate that includes the permitting scope.
In most cases, yes. A standard metal roof replacement stays on the same deck and doesn’t touch plumbing or framing; structural work only comes up if the inspection uncovers rot, a sagging deck, or a load issue the new roof triggers. We flag anything structural in writing before proceeding.
Expect $15,000 to $40,000 depending on roof size, pitch, access, material spec, and permit scope. Call (888) 427-1733 for an exact quote; estimates are free and we put every line item in writing.
Material warranties come from the panel manufacturer, and all our workmanship is covered by the 730-Day Done Right Promise, one of the longest workmanship guarantees in the residential space. If something isn’t right, we make it right.
Get a Free Metal Roofing Estimate in Malibu
A free on-site estimate for metal roofing in Malibu starts with a roof and attic inspection, a written condition report, and a line-item price that includes permits, tear-off, decking, panels, and inspection. Call (888) 427-1733 and a live person picks up, any hour, any day. We also handle Roofing more broadly, and homeowners often pair a metal roof with Window Replacement in Malibu or Impact Windows & Doors in Malibu while the scaffold is already up.
Written by the team at Groundwork Construction Co..