A Groundwork company - serving Los Angeles, CA
Paver Driveways in Culver City, CA | Groundwork Construction Co. of Los Angeles

Paver Driveways in Culver City - Free Measure, Itemized Written Quote

Free on-site measure and a written price per square foot before we book you in. Proper base preparation and sealed edges, because a cheap base is why driveways crack.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Driveway & paversDriveway & pavers
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Paver Driveways in Culver City, CA: What the Work Actually Involves

A paver driveway in Culver City runs $7,000 to $18,000 for most residential lots, and a typical job takes 4 to 7 working days from tear-out to the final sweep of joint sand. The first day is demo and haul-off; day two is excavation and base; days three and four are compaction and sand setting; days five and six are paver laying and cuts; the last day is edge restraint, joint sand, and a walkthrough. Call (888) 427-1733 to schedule a free on-site estimate, and we’ll measure your actual square footage and give you a written line-item price with no change orders.

Call (888) 427-1733

How We Build a Paver Driveway Here, Stage by Stage

Most crews quote a paver driveway as a two-number job: square footage and price per square foot. That hides all the work that decides whether the driveway looks the same in five years, and it’s why two bids that seem $3,000 apart often aren’t the same job at all. Here’s the sequence we actually run, and what you’ll be deciding at each stage.

Stage 1: Site walk and utility locate (day of estimate, about 60 minutes)

We measure the apron width, check the slope from garage floor to sidewalk, and mark where the gas line, water main, and irrigation run. On Culver City lots built between the 1920s and 1960s, the water shutoff is often right at the sidewalk in the parkway strip, and a new driveway apron can’t cover it. You’ll decide here whether the apron stays its current width or gets widened, which is one of the biggest cost levers.

Stage 2: Demo and haul-off (day 1)

Existing concrete, asphalt, or old pavers come out with a mini-excavator and slab breaker, and we haul the debris to a licensed facility. A single-car driveway of roughly 400 square feet usually takes one day; a double driveway with a deep failed slab can run into a second day. You’ll decide whether the old material gets reused as base (rarely worth it) or leaves the site.

Stage 3: Excavation, base, and compaction (days 2 and 3)

This is where a paver driveway lives or dies. We dig down 8 to 12 inches depending on your soil and traffic load, lay geotextile fabric, then build the base in 2-inch lifts of crushed aggregate, compacting each lift with a plate compactor before the next. Skipping lifts is the single most common shortcut we see from other bids. The base gets laser-checked for slope so water runs to the street, not toward your garage or foundation. You’ll confirm the final grade before we move on; once pavers go down, changing grade means starting over.

Stage 4: Setting bed and paver installation (days 4 and 5, sometimes 6)

We screed a 1-inch setting bed of washed concrete sand, then lay pavers in the pattern you chose, running the herringbone or running-bond field from a chalked line so rows stay square. Edge cuts along the apron and driveway edges are made with a wet saw for clean faces. A 500-square-foot driveway is usually two days of laying and cutting for a two-person crew.

Stage 5: Edge restraint, joint sand, and walkthrough (final day)

We spike in a rigid edge restraint along the open sides, sweep polymeric joint sand into the gaps, mist it to activate, and compact the field one last time. Then we walk the finished driveway with you, checking transitions and cleaning up. You’ll get the maintenance sheet, the manufacturer’s warranty for the pavers, and our 730-Day Done Right Promise covering the installation itself: if a joint settles or an edge fails, we come back and make it right.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Your Material and Pattern Choices, and What Each One Costs You

The paver itself is maybe 30 to 40 percent of the installed cost, but it’s the choice you’ll live with longest. Here’s what we actually lay in Culver City and the honest trade-off of each.

  • Concrete pavers, standard grade: The workhorse. Interlocking, 60mm thick, sold in modular sizes. Color runs from buff to charcoal, and fading is minimal because the color goes through the paver. Fits a tight budget and holds up to daily parking. This is what most of our Culver City paver driveway work uses.
  • Concrete pavers, tumbled or premium finish: Adds roughly 15 to 25 percent to the paver cost. The tumbled edge reads older and softer, which suits the Spanish bungalows in Carlson Park and Sunkist Park better than a crisp modern edge.
  • Clay brick pavers: The warmest look, and it’s what you see on the 1920s-era homes near the Culver Steps and downtown. Costs more per square foot and needs a sand-set detail that’s fussier to install, but a clay brick driveway can last decades.
  • Permeable pavers: Open-graded joints and a base that lets water drain through. Worth considering if your lot pools water after winter storms, and it can help if you’re also building out back. Higher installed cost, but it handles the occasional heavy rain we get in Culver City without a puddle at the garage.
  • Pattern choice: Herringbone and running bond are the standard for a driveway because they interlock against tire torque. Basketweave and large-format looks fine at the front walk but can shift under turning wheels. Your decision, but we’ll tell you which ones hold.

We set pavers on a proper base with polymeric joint sand and use Sakrete’s setting-bed products where a mixed bed is called for. The brand on the bag matters less than the base depth and compaction, so we keep that honest rather than selling the label.

What Paver Driveways Cost in Culver City, CA

Paver driveway installation in Culver City runs $7,000 to $18,000 for a typical residential job. The wide range isn’t a hedge; it tracks the actual variables below. Here’s how we break down a written estimate:

Line item Typical range
Demo and haul-off of existing surface $800 – $2,500
Excavation, base, and compaction $2,000 – $5,500
Pavers and setting materials $2,500 – $7,000
Edge restraint and joint sand $400 – $1,200
Apron work, cuts, and finish $700 – $2,000

What pushes a job toward the high end: square footage over 600 feet, a failed existing slab that has to come all the way out, relocating the parkway strip or water shutoff, a clay brick or permeable paver choice, and any driveway widening that triggers a new apron. What keeps it near the low end: a small single-car driveway, a sound existing base you’re replacing on top, and standard concrete pavers in a simple pattern. Call (888) 427-1733 for an exact quote, free, and in writing.

A written estimate from us lists each line above separately so you can see what you’re paying for. What it doesn’t include unless we call it out: relocating a gas meter, repairing a cracked garage slab, or adding a drainage channel. We tell you upfront so there are no change orders mid-job.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

What Culver City Homes Specifically Do to This Job

Culver City’s older housing stock is the thing that actually shapes a paver driveway here. Most of the homes we work on were built between the 1920s and 1940s in Carlson Park, Culver Crest, and Sunkist Park, and a lot of them still have the original concrete apron, a garage that was widened or re-graded at some point, and drainage that runs toward the house. When we tear out a driveway on one of these lots, we often find that the garage slab has settled and the apron needs to be re-poured or the pavers need a deeper base to bridge it. That’s a conversation we have before demo, not after. The wet winters and persistent ocean moisture also mean we build in a slight fall toward the street and use a joint sand that resists washout. And because the city has design review in the Carlson Park Historic District for exterior changes and a seismic-retrofit push, if your driveway work is part of a larger project, it’s worth pairing it with ADU Design & Permitting in Culver City or Garage Conversion ADU in Culver City so permitting gets reviewed together rather than piecemeal. We work throughout Culver City, from the flats near Sepulveda to the Crest, and we know what the inspectors here look for on a driveway apron and grade. If your paver driveway is part of a full Driveway & Pavers in Culver City scope that includes patios or a front walk, we’ll sequence them together. You can also browse our broader Driveway & Pavers service to see how the pieces fit.

Serving Culver City, CA – Our Local Coverage Area

We serve Culver City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked – Paver Driveways in Culver City

Schedule a Free Paver Driveway Estimate in Culver City

We’ll come to your Culver City property, measure the actual driveway, check the base and drainage, and leave you with a written line-item estimate at no cost. A real person answers when you call, and the price we quote is the price you pay. Call (888) 427-1733 to schedule your free estimate.

Written by the team at Groundwork Construction Co..

Why Culver City Chooses Groundwork Construction Co. of Los Angeles

We set the standard for paver driveways in Culver City.

No Change-Order Surprises

The written quote you sign is the price you pay. Anything we find mid-job gets priced and approved by you in writing before we touch it.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Culver City

Getting your paver driveways project started is simple.

1

Call or Request a Free Estimate

Tell us about your paver driveways project and we set up a free visit. No obligation and no hidden fees.

2

Licensed Estimator Visits

A licensed, insured estimator inspects and measures on site, then gives you a clear written price.

3

Scheduled and Done Right

Your crew does the work on the date in your quote, backed by our workmanship warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local paver driveways pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Culver City Customers Say

Trusted by homeowners across Culver City and surrounding areas.

★★★★★

"Change orders were written down and priced before the work happened, every single time. No surprise at the end."

Keisha Robinson
★★★★★

"The finished work is exactly what we wanted. It did run about three weeks over, mostly waiting on a cabinet delivery that was out of his hands, though I would have liked more updates during that stretch."

Dev Sharma
★★★★★

"He pulled the permits himself, scheduled every sub and ran the inspections. I made one decision a week and otherwise stayed out of it, which is exactly what I was paying for."

Robert Sullivan

Ready for Paver Driveways in Culver City?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast after-hours help in Culver City.

(888) 427-1733

Request a Free Estimate in Culver City

Tell us about your paver driveways needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Local Service Coverage
Call Now - 24/7 Dispatch